QuadroM-E1/T1 Manual I: Installation Guide
Configuring the QuadroM-E1/T1
QuadroM-E1/T1; (SW Version 5.2.x)
42
Fig. I-40: Call Routing Wizard - Routing Call Settings page
Use Extension Settings is applicable to SIP and IP-PSTN call types only and allows you to
select the extension (also Auto Attendant) on behalf of the call that will be placed. The SIP
settings of the selected extension will be used as the caller information. If no entry is se-
lected in this list, the original caller information will be kept. If the Keep original DID check-
box is selected, the called destination will receive the original caller’s information, rather than
the information of extension selected from the Use Extension Settings list.
When the checkbox Add Remote Party ID is selected the Remote-Party-ID parameter is
sent to the destination side when establishing a call.
SIP Tunnel drop-down list appears only when the “SIP_Tunnel” Destination Type is se-
lected on the previous page. The list is used to select the particular SIP tunnel to route the
calls through the corresponding Quadro.
Destination Host and Destination Port require the host name or the IP address and the
port number of the destination or the SIP server. As Quadro devices use port 5060 per de-
fault, enter 5060. These fields are named Modified Destination Host and Modified Desti-
nation Port correspondingly if the Pattern field on the first page of this wizard contains “@”
symbol.
User Name and Password are identification settings for public SIP servers or servers re-
quiring authentication. Leave these fields empty.
Enable Activity Timeout checkbox is used to limit time-to-live period of routing pattern
(makes sense if accept or failure feedback arrives too late from the destination). Checkbox
selection enables the Activity Timeout text field which is used to insert a routing pattern ac-
tivity timeout (in the range from 1 to 180 seconds). When timeout is configured, the routing
pattern will be active within the defined time frame and if no response has been received
from the destination during that period, the pattern will be stopped and next routing rule
might be optionally considered (depending on the Fail Reason configuration on the corre-
sponding pattern).
The Restrict the Number of Simultaneous Calls checkbox is only available for IP-PSTN
call type and is used to restrict the number of simultaneous calls to the public SIP server
with the same username at the same time. This checkbox enables Allowed Call Count text
field which requires the number of simultaneous calls allowed in a range from 1 to 64. If you
leave this field empty, no limitation will apply to the number of simultaneous logons.
Use RTP Proxy checkbox is available for SIP, H323 and IP-PSTN call types and is applica-
ble only when route is used for calls through Quadro between peers both located outside the
Quadro. When this checkbox is selected, RTP streams between external users will be
routed through Quadro, otherwise, when checkbox is not selected, RTP packets will be mov-
ing directly between peers.
Voice Transcoding checkbox is available for SIP, H323 and IP-PSTN call types and is
meaningful when an extension is selected from the Use Extension Settings drop down list.
Checkbox selection results the voice transcoding when performing IP calls through Quadro.
Independent on the codecs supported by the caller, Quadro will use the codecs of the ex-
tension selected from the Use Extension Settings drop down list to establish a call with the
Destination. If the Destination supports either of the codecs configured for the used exten-
sion, the call between the caller and the Destination will be established by the first preferred
codec of the Destination. If the Destination does not support either of the codecs configured
for the used extension, the call will be disconnected.
The Call Duration Limit checkbox is available for SIP, IP-PSTN and PSTN call types and is
used to limit the duration of the call placed with the selected routing rule. If this checkbox is
not selected, the call duration will be unlimited. This checkbox selection enables the Maxi-
mum Duration text field where the maximum duration of the call (in seconds) should be de-
fined. Once the call duration reaches the value defined here, the call will be disconnected
without prior notice.
Summary of Contents for QuadroM-E1
Page 1: ......