Epson SC-S40600 Series User Manual Download Page 89 | Manualshive

Page: 89 / 157

background image

Observe the following cautions when storing the printer
and ink cartridges/ink supply units that were removed
during use.

U

“Notes when not using the printer” on page 21

U

“Notes on handling ink cartridges/ink supply units”

Restarting use of the printer

c

Important:

When restarting use of the printer, charge the
printer with ink. When charging with removed ink
cartridges/ink supply units, have new ink
cartridges/ink supply units on hand as a
precaution.

Switch on the power and follow the on-screen
instructions.

When first printing after restarting use, perform a
nozzle check and check that there are no clogs.

U

“Printing nozzle check patterns” on page 85

Change Color Mode
(SC-S80600 Series/
SC-S80600L Series only)

Change the color mode as follows on the printer as
necessary.

❏

10 color mode (WH) <= => 10 color mode (MS)

❏

10 color mode (WH) <= => 9 color mode

❏

10 color mode (MS) <= => 9 color mode

Notes on Changing

The time required and preparation for Change Color
Mode are shown below.

Time required: up to approximately 1 hour

The time required to complete the change varies
according to the current color mode.

What you need:

❏

When changing the spot color to use (WH <= =>
MS)
Ink cartridge/ink supply unit of the color to which
you changed 1
Cleaning cartridge/cleaning ink supply unit 1

Note:

When changing the spot color, eject ink from the
tubes and wash them using a cleaning liquid to
avoid mixing colors, and then switch to the new
spot color.

❏

For 9 color mode
Cleaning cartridge/cleaning ink supply unit 1

❏

For 10 color mode
Ink cartridge/ink supply unit of the color to be used
1

c

Important:

If the installed cleaning cartridges/cleaning ink
supply units or OR/WH/MS ink cartridges/ink
supply units are running low on ink, you may not be
able to change the ink.

❏

You can change the ink immediately after
appears for the remaining ink levels for the ink
cartridges/ink supply units; however, you
cannot change the ink if there is an

Ink

Expended

error.

❏

If there is an insufficient amount of ink
remaining, have new ink cartridges/ink supply
units on hand as a precaution.

Timing when Changing from 10
to 9 Colors

If you do not print using WH/MS inks during the period
shown in the table below, switch to 9 color mode to
avoid consuming WH/MS inks.

As well as printing, the printer also consumes ink during
auto ink circulation.

SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide

Maintenance

89

«
...
87
88
89
90
91
...
»

Summary of Contents for SC-S40600 Series






























































































































































Reviews:

No comments

Related manuals for SC-S40600 Series

Brand: Oce Pages: 192

Brand: Oce Pages: 22

Brand: Oce Pages: 41

Brand: Oce Pages: 28

Brand: Oce Pages: 6

Brand: QMS Pages: 104

Brand: Oce Pages: 386

Brand: Oce Pages: 2

Brand: Oce Pages: 27

Brand: Oce Pages: 324

Brand: Datamax Pages: 2

Brand: KIP Pages: 103

VersaLink C405/N

Brand: Xerox Pages: 256

Brand: Cycjet Pages: 26

Brand: POS-TECHNOLOGY Pages: 40

Brand: Riso Pages: 208

Brand: Xerox Pages: 150

Brand: Oki Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands