manualshive.com logo in svg

Epson S1D13706, Technical Manual, Page: 133 / 672

Share
Download
Epson S1D13706 Technical Manual Download Page 133

Epson Research and Development

Page 127

Vancouver Design Center

Hardware Functional Specification

S1D13706

Issue Date: 01/11/13 

X31B-A-001-08

bit 3 and bit 0

CV Pulse Force High (bit 3) and CV Pulse Enable (bit 0)
These bits control the CVOUT pin and CV Pulse circuitry as follows.

When CVOUT is forced low or forced high it can be used as a general purpose output.

Note

1

 Bit 3 must be set to 0 and bit 0 must be set to 1 before initiating a new burst using the 

CV Pulse Burst Start bit.

2

 The CV Pulse circuitry is disabled when Power Save Mode is enabled.

bit 2

CV Pulse Burst Status
This is a read-only bit. A “1” indicates a CV pulse burst is occurring. A “0” indicates no 
CV pulse burst is occurring. Software should wait for this bit to clear before starting 
another burst.

bit 1

CV Pulse Burst Start
A 1 in this bit initiates a single CVOUT pulse burst. The number of clock pulses generated 
is programmable from 1 to 256. The frequency of the pulses is the divided CV Pulse 
source divided by 2, with 50/50 duty cycle. This bit should be cleared to 0 by software 
before initiating a new burst.

Note

This bit has effect only if the CV Pulse Enable bit is 1.

bit 0

CV Pulse Enable
See description for bit 3.

Table 8-16: CV Pulse Control

Bit 3

Bit 0

Result

0

1

CV Pulse circuitry enabled

(controlled by REG[B1h] and REG[B2h])

0

0

CVOUT forced low

1

x

CVOUT forced high 

x = don’t care

Summary of Contents for S1D13706

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments