manualshive.com logo in svg

Epson S1D13505, Technical Manual

The Epson S1D13505 Technical Manual provides comprehensive instructions and detailed information on operating and troubleshooting the Epson S1D13505 product. Available for free download on our website, this manual equips users with a valuable resource to enhance their experience and maximize the potential of their Epson S1D13505.

Share
Download
background image

Epson Research and Development

Page 13

Vancouver Design Center

Interfacing to the Motorola MPC821 Microprocessor

S1D13505

Issue Date: 01/02/05 

X23A-G-008-05

3  S1D13505 Host Bus Interface

The S1D13505 implements a 16-bit native PowerPC host bus interface which is used to 
interface to the MPC821 microprocessor.

The PowerPC host bus interface is selected by the S1D13505 on the rising edge of 
RESET#. After releasing reset the bus interface signals assume their selected configuration. 
For details on S1D13505 configuration, see Section 4.3, “S1D13505 Hardware Configu-
ration” on page 18.

Note

At reset, the Host Interface Disable bit in the Miscellaneous Disable Register 
(REG[1Bh] bit 7) is set to 1. This means that only REG[1Ah] (read-only) and 
REG[1Bh] are accessible until a write to REG[1Bh] sets bit 7 to 0 making all regis-
ters accessible. When debugging a new hardware design, this can sometimes give the 
appearance that the interface is not working, so it is important to remember to clear this 
bit before proceeding with debugging.

3.1  PowerPC Host Bus Interface Pin Mapping

The following table shows the functions of each host bus interface signal.

Table 3-1: PowerPC Host Bus Interface Pin Mapping

S1D13505

Pin Names

PowerPC

AB[20:0]

A[11:31]

DB[15:0]

D[0:15]

WE1#

BI

M/R#

External Decode

CS#

External Decode

BUSCLK

CLKOUT

BS#

TS

RD/WR#

RD/WR

RD#

TSIZ0

WE0#

TSIZ1

WAIT#

TA

RESET#

RESET#

Summary of Contents for S1D13505













































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1D13505

Cabletron Systems Netlink FRX4000 Installation And Setup Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 8
Cabletron Systems 9C300-1 Upgrade Instructions preview
9C300-1
Brand: Cabletron Systems Pages: 4
Lantronix SISPM1040-582-LRT Quick Start Manual preview
SISPM1040-582-LRT
Brand: Lantronix Pages: 2
Lantronix SDS1101 Quick Start Manual preview
SDS1101
Brand: Lantronix Pages: 7
Seattle Computer Products 8086 CPU Instruction Manual preview
8086 CPU
Brand: Seattle Computer Products Pages: 31
Patton electronics FORESIGHT 6300 User Manual preview
FORESIGHT 6300
Brand: Patton electronics Pages: 145
Accusys ACS-7630 User Manual preview
ACS-7630
Brand: Accusys Pages: 34
ICOP Technology VDX-6354RD User Manual preview
VDX-6354RD
Brand: ICOP Technology Pages: 42
H3C BT1004E Manual preview
BT1004E
Brand: H3C Pages: 34
CyberResearch CPBF PMX-233 User Manual preview
CPBF PMX-233
Brand: CyberResearch Pages: 59
NXP Semiconductors i.MX 8M Mini LPDDR4 EVK User Manual preview
i.MX 8M Mini LPDDR4 EVK
Brand: NXP Semiconductors Pages: 20
ADTRAN 1200127L1 User Manual preview
1200127L1
Brand: ADTRAN Pages: 20
CAME ZG6 Installation Manual preview
ZG6
Brand: CAME Pages: 14
Intel RS2BL040 - Raid Controller Configuration Manual preview
RS2BL040 - Raid Controller
Brand: Intel Pages: 5
Behringer MU-A043666 Quick Start Manual preview
MU-A043666
Brand: Behringer Pages: 12
Jennic JN5148 Reference Manual preview
JN5148
Brand: Jennic Pages: 14
Acqiris SA240P User Manual preview
SA240P
Brand: Acqiris Pages: 89
Fujitsu F2MC-16FR User Manual preview
F2MC-16FR
Brand: Fujitsu Pages: 14

Brands by name

Popular brands

Load more brands