Epson S1C17602 Technical Manual Download Page 199

Page: 199 / 368

19 SPi

S1C17624/604/622/602/621 TeChniCal Manual

Seiko epson Corporation

19-1

SPI

SPi Module Overview

19.1

The S1C17624/604/622/602/621 includes a synchronized serial interface module (SPI).
The following shows the main features of the SPI:

• Number of channels: 1 channel

• Supports both master and slave modes.

• Data length: 8 bits fixed

• Supports both MSB first and LSB first modes.

• Contains one-byte receive data buffer and one-byte transmit data buffer.

• Supports full-duplex communications.

• Data transfer timing (clock phase and polarity variations) is selectable from among 4 types.

• Can generate receive buffer full and transmit buffer empty interrupts.

Figure 19.1.1 shows the SPI module configuration.

Shift register

Receive data

buffer (1 byte)

SDI

PCLK

Internal bus

ITC

SPI Ch.

Bus I/F

and

control

registers

SPICLK

#SPISS

Shift register

Transmit data

buffer (1 byte)

Clock/transfer control

SDO

T16 Ch.1

output clock

Interrupt

control

1/4

1.1 SPI Module Configuration

Figure 19.

notes: • In the S1C17602/621, the transmit buffer empty interrupt can only be used in master mode.

In the S1C17624/604/622, the transmit buffer empty interrupt can be used in both master and
slave modes.

• The letter ‘

’ in register and pin names refers to a channel number (0).

Example: SPI_CTL

Ch.0: SPI_CTL0 register

SPi input/Output Pins

19.2

Table 19.2.1 lists the SPI pins.

2.1 List of SPI Pins

Table 19.

Pin name

i/O

Qty

Function

SDI0 (Ch.0)

SPI data input pin
Inputs serial data from SPI bus.

SDO0 (Ch.0)

SPI data output pin
Outputs serial data to SPI bus.

Summary of Contents for S1C17602

















































































































































































































































































































































































Search results

Summary of Contents for S1C17602

Reviews:

Related manuals for S1C17602

Brands by name

Popular brands

Epson S1C17602, Technical Manual

Search results

Summary of Contents for S1C17602

Reviews:

Related manuals for S1C17602

Brands by name

Popular brands