Epson RP-U420 Series Specification Download Page 61

Page: 61 / 84

Confidential

EPSON

TITLE

SHEET
REVISION

NO.

SHEET

RP-U420 series

Specification

(STANDARD)

ESC <

[Name]

Return home

[Format]

ASCII

ESC

Hex

Decimal

[Function]

Detects the home position again; then moves the print head to the standby position.

ESC = n

[Name]

Select device

[Format]

ASCII

ESC

Hex

Decimal

[Range]

≤

[Default]

= 1

[Function]

Selects device to which the host computer sends data, using n as follows:

Function

Enables printer.

Enables customer display.

Enables printer and customer display.

[Description]

•

When the printer is disabled, it ignores all data except for real-time commands until it is
enabled by this command.

ESC ? n

[Name]

Cancel user-defined characters

[Format]

ASCII

ESC

Hex

Decimal

[Range]

≤

126

[Function]

Deletes user-defined character pattern that corresponds the specified character code.

•

specifies the character code corresponding to the user-defined character to be

canceled.

[Description]

•

If a user-defined character has not been defined for the specified character code, the
printer ignores this command.

•

After the user-defined character is canceled, the corresponding pattern for the internal
character is printed.

Summary of Contents for RP-U420 Series





















































































Search results

Summary of Contents for RP-U420 Series

Reviews:

Related manuals for RP-U420 Series

Brands by name

Popular brands

Epson RP-U420 Series, Specification

Search results

Summary of Contents for RP-U420 Series

Reviews:

Related manuals for RP-U420 Series

Brands by name

Popular brands