Epson LQ-570e User Manual Download | Manualshive

Page: 157 / 248

background image

7

Troubleshooting

7-17

Aligning Vertical Lines in Your Printout

If you notice that the vertical lines in your printout are not
properly aligned, you can use the printer’s bidirectional
adjustment mode to correct this problem.

Note:

❏

To complete the steps below, you need four sheets of A4 or letter size
single-sheet paper or four pages of continuous paper that are at least
279 mm (11 inches) long and 241 mm (9.5 inches) wide. See Chapter
2 for instructions on loading continuous paper, or Chapter 3 for
instructions on loading single sheets.

❏

If you use single sheets, you need to load a new sheet of paper each
time the printer ejects a printed sheet onto the paper guide.

Follow these steps to perform the bidirectional adjustment:

1. Make sure paper is loaded and the printer is turned off.

c

Caution:

Whenever you turn off the printer, wait at least five seconds
before turning it back on; otherwise you may damage the
printer.

2. While holding down the

Pause

button, turn on the printer.

The printer enters the bidirectional adjustment mode and
then prints instructions and the first set of alignment patterns.

3. As described in the instructions, compare the alignment

patterns and select the pattern with the best alignment.

4. Follow the instructions to print the remaining sets of

alignment patterns and select the pattern with the best
alignment in each set.

5. After you select the best pattern in the final set of alignment

patterns, turn off the printer and exit the bidirectional
adjustment mode. Your selections are saved automatically.

«
...
155
156
157
158
159
...
»

Summary of Contents for LQ-570e

























































































































































































































































Reviews:

No comments

Related manuals for LQ-570e

Brand: Oce Pages: 192

Brand: Oce Pages: 22

Brand: Oce Pages: 41

Brand: Oce Pages: 28

Brand: Oce Pages: 6

Brand: QMS Pages: 104

Brand: Oce Pages: 386

Brand: Oce Pages: 2

Brand: Oce Pages: 27

Brand: Oce Pages: 324

Brand: Oki Pages: 222

Brand: Oki Pages: 4

Brand: Oki Pages: 160

Brand: Oki Pages: 167

Brand: Oki Pages: 116

Brand: Oki Pages: 52

Brand: Oki Pages: 331

Brand: Oki Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands