Epson LQ-570e User Manual Download | Manualshive

Page: 14 / 248

background image

4

Getting to Know Your Printer

Available Paper Paths

Your printer provides a variety of paper paths for printing on
continuous and single-sheet paper. As described below, paper can
be fed into the printer from the top, front, bottom, or rear. You can
select the paper path that best suits your current printing needs.

Printing on continuous paper

You can choose from two tractor positions (push and pull) and
three paper entry slots (front, rear, and bottom) for continuous
paper printing. This section helps you determine which paper
paths and tractor positions are best for your continuous paper
printing needs. See the appropriate sections in Chapter 2 for
tractor installation and paper loading instructions.

Using the push tractor

If you often need to tear off sheets of continuous paper (for
example, if you are printing purchase orders or sales slips), it is
best to use the push tractor. This allows you to use the printer’s
tear-off edge to easily tear off printed sheets of continuous paper
at the perforation. Also, when continuous paper is loaded on the
push tractor, you can load single sheets of paper from the paper
guide without removing the continuous paper from the tractor.

The tractor is installed in the rear push position when the printer
is shipped. See the table below for details about the corresponding
paper-feeding path.

Tractor position

Description

push

Caution:

Do not load continuous paper with labels in the rear
slot; the labels may come off their backing sheet
inside the printer and cause a paper jam.

«
...
12
13
14
15
16
...
»

Summary of Contents for LQ-570e

























































































































































































































































Reviews:

No comments

Related manuals for LQ-570e

Brand: Eazao Pages: 50

Brand: B9Creations Pages: 25

Brand: F+D Feinwerk- und Drucktechnik Pages: 41

Brand: Xerox Pages: 414

Brand: Raise3D Pages: 32

Brand: Panasonic Pages: 166

imageRUNNER 2545i

Brand: Canon Pages: 37

Donation Point Even

Brand: Quest Payment Systems Pages: 2

Brand: Oki Pages: 40

Brand: Partex Pages: 12

Brand: Tektronix Pages: 178

Brand: Ricoh Pages: 2

Brand: Kyocera Pages: 76

Pixma G2030 Series

Brand: Canon Pages: 351

PIXMA G2070 Series

Brand: Canon Pages: 358

Brand: Canon Pages: 430

Brand: Canon Pages: 430

Brand: Canon Pages: 271

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands