Epson EPL-5500W Service Manual Download Page 81

Page: 81 / 105

5.4.2 Print Quality Anomalies

This section describes how to isolate possible causes of a print quality problem.

Table 5-12. Print Quality Anomalies

Symptom

Possible Cause

Part Name

Check Item

Remedy

Low image density

Poor
development

PWB-F board

—

Replace the PWB-F
board.

Image transfer
problem

Image transfer
unit

Check to see if the
surface of image
transfer unit is
damaged.

Replace the image
transfer unit.

PWB-F board

—

Replace the PWB-F
board.

Defective PC
drum

Photoconduc-
tor unit

—

Replace the
photoconductor unit.

Improper print
density setting

—

Adjust the print
density using the
printer settings.

Foggy background

Poor develop-
ment

Toner
cartridge

—

Replace the toner
cartridge.

Improper
charging

Drum charge

—

Replace the PWB-F
board.

Check the wiring of
the PC drum charging
bias line.

Replace the
photoconductor unit.

Improper print
density setting

—

Adjust the print
density using the
printer settings.

Troubleshooting

EPL-5500W Service Manual

5-8

Rev. A

Summary of Contents for EPL-5500W










































































































Search results

Summary of Contents for EPL-5500W

Reviews:

Related manuals for EPL-5500W

Brands by name

Popular brands

Epson EPL-5500W, Service Manual

Search results

Summary of Contents for EPL-5500W

Reviews:

Related manuals for EPL-5500W

Brands by name

Popular brands