Epson EPL-5500W Service Manual Download Page 23

Page: 23 / 105

1.4.2 Display of Messages

This printer indicates two types of messages with the status message window for the printer driver on the PC.

1.4.2.1 Status Messages

This section describes the status messages.

Table 1-6. Status Messages

Message

Status

Printer ready

Printer is ready.

Printing

Printer is printing.

Manual feed

Printer is loading paper from manual feed slot.

Paused

Printer is in pause mode.

Printing stopped

Printer is stopping during printing of a job.

Please wait

Printer is in the wait condition.

Paused printer warming up

Printer is warming up.

Printer warming up

Printer is warming up.

1.4.2.2 Error Messages

This section describes error messages, what they indicate, and what measures to take to eliminate the error.

Table 1-7. Error Messages

Message

Status

Measures

Configuration error

The user is unable to redirect
a port, or system software
cannot find a file to complete
a request.

Check the printer connection
port, and reinstall the driver.

Low memory

Memory in PC has run out.

Add the memory to the PC.

No local printer

The printer is not connected
to the local port when you are
using PCL emulation.

PCL emulation does not
support a network.

Status not available

The printer does not return
status information.

Check the printer connection.

Check printer/ cable

The printer does not return
status information.

Check the printer connection.

Service error

Printer is damaged.

Service required.

Clear paper jam

A paper jam occurred.

Open the cover and remove
the jammed paper. Then
close the cover.

General Description

EPL-5500W Service Manual

1-10

Rev. A

Summary of Contents for EPL-5500W










































































































Search results

Summary of Contents for EPL-5500W

Reviews:

Related manuals for EPL-5500W

Brands by name

Popular brands

Epson EPL-5500W, Service Manual

Search results

Summary of Contents for EPL-5500W

Reviews:

Related manuals for EPL-5500W

Brands by name

Popular brands