Epson EPL-5500W Service Manual Download Page 77

Page: 77 / 105

Table 5-3. The Printer Does Not Operate at All

Cause

Step

Checkpoint

Finding

Solution

Connector CN207 on the
C180 MAIN board may be
disconnected.

Is connector CN207 on the
C180 MAIN board
disconnected?

Yes

Connect CN207
on the board.

The fuse on the PWB-E
board may be blown.

Has the fuse blown on the
PWB-E board?

Yes

Replace the fuse.

PWB-E board may be dead.

With power on, is there an
output of +5 VDC between pin
4 (+) and pin 3 (–) for CN207
on C180 MAIN board?

Replace the
PWB-E board.

C180 MAIN board may be
dead.

—

Replace the C180
MAIN board.

Table 5-4. Both LED Lights Do Not Come On

Cause

Step

Checkpoint

Finding

Solution

The C180 MAIN board may
be dead.

If you replace the C180 MAIN
board, do the LEDs come on?

Yes

Replace the C180
MAIN board.

Table 5-5. Clear Paper Jam (1)

Cause

Step

Checkpoint

Finding

Solution

The paper take-up sensor
flag position may be
incorrect.

Is the paper take-up sensor
flag position OK?

Reposition the
paper take-up
sensor flag.

The paper exit sensor flag
position may be incorrect.

Is the paper exit sensor flag
position OK?

Reposition the
paper exit sensor
flag.

The paper take-up sensor
connector may be
disconnected.

Is the paper take-up sensor
connector disconnected?

Yes

Connect it.

The paper exit sensor
connector may be
disconnected.

Is the paper exit sensor
connector disconnected?

Yes

Connect it.

The paper exit sensor may
be bad.

—

Replace it.

The paper take-up sensor
may be bad.

—

Replace it.

Troubleshooting

EPL-5500W Service Manual

5-4

Rev. A

Summary of Contents for EPL-5500W










































































































Search results

Summary of Contents for EPL-5500W

Reviews:

Related manuals for EPL-5500W

Brands by name

Popular brands

Epson EPL-5500W, Service Manual

Search results

Summary of Contents for EPL-5500W

Reviews:

Related manuals for EPL-5500W

Brands by name

Popular brands