Epson AcuLaser Color 2000 Service Manual Download Page 68 | Manualshive

Page: 68 / 204

background image

EPSON AcuLaser C2000

Revision C

Operating Principles

Printing Process

68

2.2.1 Paper Feed Mechanism

EPSON AcuLaser C2000 has 2 paper feed methods:
Tray 1 (150 sheets) + Tray 2 (500 sheets)

Optional 500 sheets cassette unit (Tray 3) is also available.

2.2.1.1 Tray 1

When the paper feed solenoid (SL 8) is turned ON, the driving power from
the transfer motor (M1) is transmitted to the paper feed roller via the
paper feed clutch (one-way clutch). Paper pushing plate is pushed to the
paper feed roller, and the paper feed roller rotates. The printer feeds the
top sheet of paper. Paper fed by the paper feed roller is carried to the
timing roller via transportation roller.

Separation pad method is used in order to separate each paper and
prevent feeding the second paper together.

If paper is OHP, it is detected by OHP sensor (PC11).

Paper empty switch (S9) detects if there is paper on Tray 1.

Tray 1 position sensor (PC15) detects if Tray 1 is pulled and the paper
pushing plate is ready to push paper to the paper feed roller.

Figure 2-7. Tray 1

Paper Feed Solenoid (SL8)

Paper Feed Back View

Paper Feed Roller

Tray 1 empty Switch (S9)

OHP Sensor (PC11)

Tray 1 Position Sensor (PC15)

Paper Pushing Plate

Paper Feed Front View

«
...
66
67
68
69
70
...
»

Summary of Contents for AcuLaser Color 2000













































































































































































































Reviews:

No comments

Related manuals for AcuLaser Color 2000

Brand: Qls Pages: 53

Brand: Xerox Pages: 36

Brand: quadient Pages: 130

WorkCentre 7232

Brand: Xerox Pages: 13

CX PRINT SERVER 550

Brand: Xerox Pages: 166

Brand: Xerox Pages: 4

Brand: Xerox Pages: 324

Brand: Samsung Pages: 549

Brand: Canon Pages: 2

imageRUNNER C3480

Brand: Canon Pages: 92

Brand: Oki Pages: 328

MAGICARD 300plus

Brand: Ultra electronics Pages: 45

Brand: Citizen Pages: 4

Brand: Telpar Pages: 52

WorkCentre 6655i

Brand: Xerox Pages: 282

Brand: Konica Minolta Pages: 424

Brand: Roland Pages: 116

Brand: Canon Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands