Epson AcuLaser Color 2000 Service Manual Download Page 153

Page: 153 / 204

EPSON AcuLaser C2000

Revision C

Disassembly and Assembly

Disassembling Procedure

153

4.2.22 Belt Cleaner Mechanism

4.2.22.1 Left Upper Support Plate Removal

Remove the Operation Panel. (See “Operation Panel Removal” on
page -124.)

Remove the Front Inner Cover. (See “Front Inner Cover Removal” on
page -124.)

Remove the Top Cover. (See “Top Cover Removal” on page -125.)

Remove the Left Cover. (See “Left Cover Removal” on page -125.)

Remove the Rear Controller Cover. (See “Rear Controller Cover
Removal” on page -126.)

Remove the Rear Cover. (See “Rear Cover Removal” on page -127.)

Remove 5 screws securing the left upper support plate. (Upper side: 3
screws, Front rear side: 1 screw each)

Figure 4-58. Left Upper Support Plate Removal

4.2.22.2 Left Frame Plate Removal

Remove the Left Upper Support Plate. (See “Left Upper Support Plate
Removal” on page -153.)

Remove the harness from the harness saddle at the left frame.

Remove 4 screws securing the left frame plate.

Remove the harnesses from 4 connectors of the belt cleaner control
board on the left frame.

Figure 4-59. Left Frame Plate Removal

Summary of Contents for AcuLaser Color 2000













































































































































































































Search results

Summary of Contents for AcuLaser Color 2000

Reviews:

Related manuals for AcuLaser Color 2000

Brands by name

Popular brands

Epson AcuLaser Color 2000, Service Manual

Search results

Summary of Contents for AcuLaser Color 2000

Reviews:

Related manuals for AcuLaser Color 2000

Brands by name

Popular brands