Epson AcuLaser Color 2000 Service Manual Download Page 125

Page: 125 / 204

EPSON AcuLaser C2000

Revision C

Disassembly and Assembly

Disassembling Procedure

125

4.2.3.4 Top Cover Removal

Remove the Operation Panel. (See “Operation Panel Removal” on
page -124.)

Remove the cover for the optional unit cover located at the top rear
side of the Top Cover.

Remove 2 screws (1 under the option cover and the other at the rear
right securing the Top Cover and Rear Cover together), and remove
the Top Cover.

Figure 4-6. Screws Fixing the Top Cover

Through the transfer belt installation hole, release the hook fixing the
Top Cover to the printer frame and remove the Top Cover.

Figure 4-7. Hook on the Top Cover

4.2.3.5 Left Cover Removal

Remove the Top Cover. (See “Top Cover Removal” on page -125.)

Remove 3 screws securing the Left Cover.

Pull the Left Cover to the front and lift it up to release 3 hooks at the
bottom.

Move the Left Cover down to release 3 hooks along the top edge, and
remove the Left Cover.

Figure 4-8. Left Cover Removal

C H E C K

P O I N T

When installing the Left Cover to the printer frame, be sure
to set the reinforcing plate between them and fasten the
screws.

Summary of Contents for AcuLaser Color 2000













































































































































































































Search results

Summary of Contents for AcuLaser Color 2000

Reviews:

Related manuals for AcuLaser Color 2000

Brands by name

Popular brands

Epson AcuLaser Color 2000, Service Manual

Search results

Summary of Contents for AcuLaser Color 2000

Reviews:

Related manuals for AcuLaser Color 2000

Brands by name

Popular brands