EPIGY TECHNOLOGIES QUADRO 2XI Installation Manual Download Page 41 | Manualshive

Page: 41 / 63

background image

Quadro Manual I: Installation Guide

Step 2-C: Using ISDN Lines

Quadro2x, 2xi; Quadro4x, 4xi; Quadro16x, 16xi (SW Version 5.3.x)

41

For MSN service enabled,

the

Routing Settings

page is used to assign MSN numbers to

the certain destinations on the Quadro. The MSN number can be assigned to the Quadro’s
extensions, to the Auto Attendant, or to the routing agent. The destination selected from
this page will ring upon incoming call to the corresponding MSN number comes in.

The fields in the

MSN Number

column require the MSN numbers allocated to the Quadro.

Please Note:

At least one MSN number should be defined in this page. The system dis-

plays an error message if the same MSN number is used twice in this page.

The

Route Incoming Call to

drop-down lists are used to select the destination where the

incoming call addressed to the certain MSN number will be routed. Choosing the

Routing

with inbound destination number

selection will automatically use the initially dialed num-

ber to connect the destination without any additional dialing. If MSN is disabled on the

ISDN Wizard -

MSN Settings

page, the

ISDN Wizard -

Routing Settings

page contains

only one

Route Incoming Call to

drop-down list.

Selecting the

Use Default outgoing Caller ID

allows you to overwrite the source caller in-

formation with the one specified in the

Default outgoing Caller ID

field when placing out-

going calls toward the CO. The

Default outgoing Caller ID

field requires the caller ID for

the outgoing calls from the Quadro through the ISDN trunk. That number should be regis-
tered at the CO and can be one of the MSNs provided by the CO. If this checkbox is
enabled but no value is defined in the

Default outgoing Caller ID

, empty caller information

will be sent to the CO. If this checkbox is disabled, the source caller information will be for-
warded to the CO.

Select the

Advanced Settings

checkbox if you wish to adjust trunk L2 and L3 Settings

manually, otherwise leave this checkbox unselected to use the system default values.

Fig. II-35: ISDN Wizard – Routing Settings

«
...
39
40
41
42
43
...
»

Summary of Contents for QUADRO 2XI
































































Reviews:

No comments

Related manuals for QUADRO 2XI

Brand: AVM Pages: 80

SIPPBX 6200GS - RELEASE 3.0

Brand: WELLTECH Pages: 1

CAS2000 - CONNECT TO SIPPBX6200

Brand: WELLTECH Pages: 3

Brand: WELLTECH Pages: 124

Brand: DVS Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands