EPIGY TECHNOLOGIES QUADRO 2XI Installation Manual Download Page 27

Page: 27 / 63

Quadro Manual I: Installation Guide

Step 2: Configuring the Quadro

Quadro2x, 2xi; Quadro4x, 4xi; Quadro16x, 16xi (SW Version 5.3.x)

This information will be needed to be inserted in the Internet Configuration Wizard.

Uplink Configuration

Select the desired WAN Interface Protocol and enter the

WAN Interface Bandwidth

to as-

sure the quality of IP calls.

Fig. I-23: Uplink Configuration

If the available bandwidth is used to the point where the quality of an additional IP call
would suffer, then new IP calls are rejected.

The bandwidth provided by your ISP must be specified for both

Upstream

and

Down-

stream

fields

The default entry in both fields is

10000,

the maximum bandwidth of the 10

MB uplink module.

For basic DSL and cable modem service in the United States, typical

values are

300

for Upstream and

1500

for Downstream.

The

Min Data Rate

text field is used to specify the amount of bandwidth reserved for data

applications. The value entered here needs to be smaller that the value specified for

Up-

stream Bandwidth

Specify the

WAN Interface Protocol

by choosing between available WAN interface proto-

cols:

PPPoE

(Point to Point over Ethernet),

PPTP

(Point to Point Tunneling Protocol) and

Ethernet

. Use Ethernet for DHCP or static IP.

For

Ethernet

clicking

Next

will display the

WAN IP Configuration

page

PPPoE

is the

selected WAN Interface Protocol

the next page will be

PPP/PPTP Configuration

For

PPTP

WAN Interface Protocol,

PPP/PPTP Configuration

page will follow the

WAN IP Configu-

ration.

WAN IP Configuration

Your Internet Service Provider (ISP) should provide this information.

•

Assign automatically via DHCP

- The parameters are set automatically by the ISP.

This is common with cable modem and DSL service.

Summary of Contents for QUADRO 2XI
































































Search results

Summary of Contents for QUADRO 2XI

Reviews:

Related manuals for QUADRO 2XI

Brands by name

Popular brands

EPIGY TECHNOLOGIES QUADRO 2XI, Installation Manual

Search results

Summary of Contents for QUADRO 2XI

Reviews:

Related manuals for QUADRO 2XI

Brands by name

Popular brands