EPIGY TECHNOLOGIES QUADRO 2XI Installation Manual Download Page 13

Page: 13 / 63

Quadro Manual I: Installation Guide

Hardware Overview

Quadro2x, 2xi; Quadro4x, 4xi; Quadro16x, 16xi (SW Version 5.3.x)

LED indication during a firmware update

A firmware update is indicated by the red (

Fault

) and yellow (

Info

) LEDs. Both will blink si-

multaneously for about two minutes while the firmware is being updated. The Quadro will
then reboot automatically showing the boot LED sequence.

LED indication during a boot sequence

A boot sequence is indicated as follows: The red

Fault

LED will glow for a few seconds,

then the yellow

Info

LED will glow for another four or five minutes while the green

Busy

LED is blinking. Once the

Info

LED is off, the boot sequence has been completed success-

fully.

LED indication during emergency firmware upload

The red

Fault

LED and the yellow

Busy

LEDs will stop blinking alternately and start blink-

ing in parallel. This shows that Quadro has accepted the emergency firmware and is load-
ing it. After a few seconds, Quadro will boot, indicated as follows: The red

Fault

LED will

glow for a few seconds, then the yellow

Info

LED will glow for another few seconds while

the green

Busy

LED is jittering. When the yellow

Info

LED extinguishes, the boot se-

quence has been completed successfully.

Summary of Contents for QUADRO 2XI
































































Search results

Summary of Contents for QUADRO 2XI

Reviews:

Related manuals for QUADRO 2XI

Brands by name

Popular brands

EPIGY TECHNOLOGIES QUADRO 2XI, Installation Manual

Search results

Summary of Contents for QUADRO 2XI

Reviews:

Related manuals for QUADRO 2XI

Brands by name

Popular brands