manualshive.com logo in svg

enphase D380, Troubleshooting Manual

Share
Download
enphase D380 Troubleshooting Manual Download Page 33

Troubleshooting an Enphase System 

 

 2014 Enphase Energy Inc. 

August 2014 

33 

Messages and Alerts  

You can view event messages in Enlighten or in the Envoy 
interface. Event messages show a summary of the 
detected issue and a recommended action. 

 

 

ACFOOR (AC Frequency Out of Range) 

The microinverter reports that the frequency coming from 
the utility is either too low or too high as specified by UL 
standards (UL1741). The typical frequency is 60.0 Hz. 

 

Microinverter Model 

Nominal Frequency Range (Hz) 

M250 

57 to 62.5 Hz 

M215 

57 to 61 Hz 

M190 

59.3 to 60.5 Hz 

D380 

59.3 to 60.5 Hz 

M210 

59.3 to 60.5 Hz 

 

AC Frequency Out of Range

 events are usually transient, indicating an anomaly from the utility, and 

usually self-correcting by the utility. If Frequency Out of Range events persist, troubleshoot as follows. 

Although 

ACFOOR

 events can happen because of an actual frequency out-of-spec condition, these 

events more likely to occur because of either a poorly shaped AC waveform or excessive THD (Total 
Harmonic Distortion) emanating from the utility service. This type of error rarely affects just one unit, and 
usually indicates an AC service issue.  

Along with 

ACFOOR

 

events, “

Grid Gone

”

 might be occurring. This indicates 

Anti-Islanding

, which also 

sometimes occurs during 

ACVOOR (AC Voltage Out of Range)

 and 

ACFOOR

 events. 

 

 

What 

is “Anti

-Isla

nding”

? 

 

“Anti

-

islanding” is protection against the continuous operation of the inverter and part of the utility 

load while isolated from the remainder of the electric utility system.   

If power from the utility is disconnected, the utility-interactive inverter ceases to export power 
within two seconds. Anti-Islanding protects utility line workers and loads.  

Summary of Contents for D380














































Reviews:

No comments

Brands by name

Popular brands

Load more brands