manualshive.com logo in svg

enphase D380, Troubleshooting Manual

Share
Download
enphase D380 Troubleshooting Manual Download Page 12

Troubleshooting an Enphase System 

 

 2014 Enphase Energy Inc. 

August 2014 

12 

LCD is completely blank 

1.  Try another outlet (just in case). 

2.  If this fails, the Envoy unit must be replaced. There are no field replaceable parts for the Envoy. 

Contact Enphase Customer Support 

[email protected]

. 

 

LCD displays “Reset Clock”

 

If the Envoy has a current Internet connection, let it use this connection to retrieve an upgrade from 
Enlighten. This may take up to 20 minutes, depending upon the speed of the connection. You may need 
to contact Enphase Customer Support to initiate the upgrade. 

 

LCD displays “Envoy Failure”

 

This message displays after the Envoy has tried unsuccessfully three times to initialize. This may happen 
when the Envoy has been moved, and its initialization process interrupted. 

1.  Unplug the Envoy from the electrical outlet, and then plug it in again. Leave the Envoy in place for 

at least 15 minutes.  

2.  If it continues to display 

Envoy Failure

 or if it never moves beyond the Initialization stage, contact 

Enphase Customer Support. 

 

LCD displays "Scanning Inhibited" 

This message displays after an installer has used the Installer's Toolkit to provision the Envoy. Leave the 
Envoy in this condition for normal operation. If you need to re-enable scanning, contact Enphase 
Customer Support ([email protected]).  

 

 

Summary of Contents for D380














































Reviews:

No comments

Brands by name

Popular brands

Load more brands