manualshive.com logo in svg

enphase D380, Troubleshooting Manual

Share
Download
enphase D380 Troubleshooting Manual Download Page 27

Troubleshooting an Enphase System 

 

 2014 Enphase Energy Inc. 

August 2014 

27 

Microinverter and PV Module Issues

  

This section describes ways to isolate failures within 
microinverters or PV modules using: 

 

Microinverter LEDs 

 

Power Production 

 

 

Microinverter LEDs 

Startup LED Operation  

The status LED on the underside of each microinverter 
lights green about six seconds after DC power is applied. It 
remains lit solid for two minutes, followed by six green 
blinks. After that, red blinks indicate that no grid is present if 
the system is not yet energized. 

Six short red blinks when DC power is first applied to the 
microinverter indicate a failure during microinverter startup. 

(On older models, including M190, M210, and D380, the LED is on the 

edge

 of the microinverter.) 

 

LED color

 

State 

Meaning 

Green  Solid 

Normal startup 

Flashing  Transition to post start up state 

Red 

Flashing  No grid present (AC breaker is not turned on) 

Solid 

Failed microinverter start up 

 

 

Post-Startup LED Indications 

Use a handheld mirror to view indicator lights on the undersides of the microinverters. LED states are: 

 

LED color 

State 

Meaning 

Green 

Flashing  Normal operation. The microinverter is receiving messages from the Envoy and 

senses that the utility grid is within voltage/frequency specifications

.

 

Orange  Flashing  Not receiving messages from the Envoy, but is otherwise operating normally. 

The microinverter senses that the utility grid is within voltage/frequency 
specifications. Troubleshoot as described in the following sections. 

Red 

Flashing  Failed to produce power and

 not operating normally.

 The microinverter does 

not sense that the utility grid is within voltage/frequency specifications. The 
microinverter cannot produce power until this is resolved. . Troubleshoot as 
described in the following sections. 

Solid 

Fault requiring intervention.  

 

For M215-60-2LL-S22-IG, S23-IG, or S24-IG 

this indicates a “DC 

Resistance Low 

–

 

Power Off”

 fault. (continued on next page) 

LED on 
underside 
of micro-
inverter 

Summary of Contents for D380














































Reviews:

No comments

Brands by name

Popular brands

Load more brands