manualshive.com logo in svg

enphase D380, Troubleshooting Manual

Share
Download
enphase D380 Troubleshooting Manual Download Page 18

Troubleshooting an Enphase System 

 

 2014 Enphase Energy Inc. 

August 2014 

18 

 

Install a broadband router to allow multiple private LAN connections to the single WAN connection. 
See 

Setup 1

 below. 

Also, if the broadband connection is setup to only allow one Internet-connected host at a time, contact 
the ISP to change the account to allow multiple hosts to connect at one time. The ISP may 
recommend a router, or you may opt to buy one at a retailer. 

 

If the site has a wireless broadband router, purchase an ENV-120-02, the kit that includes an Envoy 
and a Wi-Fi stick. Install it as described in 

Envoy Installation and Operation Manual

 at 

http://www.enphase.com/support

.  

 

Internet service is not available on site 

Consider buying an air card or hot spot. There are some cases where this is the only Internet connectivity 
option for the site. Air cards are also called EVDO or CDMA cards and typically provided by Sprint, 
Verizon or AT&T. Purchase an air card compatible router (e.g., Cradlepoint MBR 95). Plug the air card 
into the indicated port on the router to create a LAN at the site. See 

Setup 2

 below. 

After installing the air card, you can then install the Envoy as described in the 

Envoy Installation and 

Operation Manual

 at 

http://www.enphase.com/support

.

 

 

 

 

What are LAN and WAN? 

 

WAN = The Wide Area Network is the network beyond your local premises. 
LAN  = The Local Area Network is the network within your local premises. 

Summary of Contents for D380














































Reviews:

No comments

Brands by name

Popular brands

Load more brands