manualshive.com logo in svg

enphase D380, Troubleshooting Manual

Share
Download
enphase D380 Troubleshooting Manual Download Page 42

Troubleshooting an Enphase System 

 

 2014 Enphase Energy Inc. 

August 2014 

42 

3.  In the 

clear-gfi

 menu, select 

set

. 

 

 

 

4.  Click 

Send Command

. 

 

Grid Gone 

The microinverter reports that power from the utility is no longer present or is out of voltage or frequency 
specification. In most cases, no action is required. Solar production resumes when conditions normalize. 

Enphase microinverters are 

utility interactive

 and require a connection to the utility. 

 

Verify that the solar circuit breakers are on at the load center. If all breakers are on, the condition 
should clear itself. 

 

If 

Grid Gone

 events repeatedly occur on one microinverter or only on portions of a branch, call 

Enphase Customer Support for assistance.  

 

What is a “Utility Interactive” inverter? 

 

The NEC (National Electric Code) defines this as, “An inverter intended for use in parallel with an 
electric utility to supply common loads that may deliver power to the utility.” A utility

-interactive 

inverter lets PV system owners export excess power back to the utility.  

Summary of Contents for D380














































Reviews:

No comments

Brands by name

Popular brands

Load more brands