EnGenius Neutron Series User Manual Download Page 101

Page: 101 / 107

101

Professional Installation Instruction

1. Installation Personnel

This product is designed for specific application and needs to be installed by a qualified personnel who

has RF and related rule knowledge. The general user shall not attempt to install or change the set-
tings.

2. Installation Location

The product shall be installed at a location where the radiating antenna can be kept at least

23cm

from nearby persons in normal operating conditions to meet regulatory RF exposure requirement.

3. Installation Procedure

Please refer to the user’s manual for details.

4. Warning!

Please carefully select the installation position and make sure that the final output power does not

exceed the limit set force in relevant rules. The violation of this rule could lead to serious federal pen-
alties.

Summary of Contents for Neutron Series












































































































Search results

Summary of Contents for Neutron Series

Reviews:

Related manuals for Neutron Series

Brands by name

Popular brands

EnGenius Neutron Series, User Manual

Search results

Summary of Contents for Neutron Series

Reviews:

Related manuals for Neutron Series

Brands by name

Popular brands