E-4
Convection Construction Heater
Operating Instructions and Owner’s Manual
OpERATING pRECAUTIONS
This is a propane, direct-fired, convection heater. It's intended use
is primarily temporary heating of buildings under construction,
alteration or repair.
Propane is heavier than air. If propane leaks from a connection or
fitting, it sinks to the floor, collecting there with the surrounding
air, forming a potentially explosive mixture. Obviously, propane
leaks should be avoided, so set up the propane supply with
utmost care. Read enclosed Odor Fade and Propane Sheet for
additional information about detecting propane leaks. Leak check
new connections or reconnections with a soap and water solution
and follow all connection instructions herein. Also, ask your
propane dealer for advice on the propane application and supply
installation and ask him to check it if there are any questions.
This heater was designed and certified for use as a construction
heater in accordance with ANSI Standard Z83.7/CGA 2.14-
2000. Check with your local fire safety authority if you have any
questions about your applications. Other standards govern the use
of fuel gases and heat producing products in specific applications.
Your local authority can advise you about these.
Direct-Fired means that all of the combustion products enter the
heated space. Even though this heater operates very close to 100
percent combustion efficiency, it still produces small amounts of
carbon monoxide. Carbon monoxide (called CO) is toxic. We can
tolerate small amounts but not a lot. CO can build up in a heated
space and failure to provide adequate ventilation could result in
death. The symptoms of inadequate ventilation are:
•
headache
•
dizziness
•
burning eyes and nose
•
nausea
•
dry mouth or sore throat
So, be sure to follow advice about ventilation in these operating
instructions.
When the heater is to be operated in the presence of other
people the user is responsible for properly acquainting those
present with the safety precautions and instructions, and of
the hazards involved.
saFeTY PreCauTIOns
1. Check the heater thoroughly for damage. DO NOT
operate a damaged heater.
2.
DO NOT
modify the heater or operate a heater which has
been modified from its original condition.
3.
DO NOT
light or operate heater unless the shells are
fully extended and locked into position. See enclosed
assembly sheet for instructions.
4. Use only propane gas.
5. Use only VAPOR WITHDRAWAL propane supply. If there
is any question about vapor withdrawal, ask your propane
dealer.
6. Mount the propane cylinders vertically (shutoff valve
up). Secure them from falling or being knocked over and
protect them from damage.
7. Locate propane containers at least (USA) 7 ft. (2.13m)
for 80CV and 9 ft. (2.7m) for 200CV (Canada)10 ft.
(3m) from the heater and
do not
direct exhaust toward
containers.
8.
IMPORTANT
Use only the hose and regulator assembly
provided with the heater. Match the color stripe on the
hangtag attached to the hose assembly with the color
on the label located near the propane inlet fitting on the
heater.
Inspect hose assembly before each use of the
heater. If there is excessive abrasion or wear, or hose is
cut, replace with hose assembly listed on parts list before
using heater.
9. For indoor use only. Area must be well ventilated.
Figure
1
. (also see "Operating Precautions").
10. If at any time gas odor is detected, IMMEDIATELY
DISCONTINUE operation until the source of gas has
been located and corrected. Read enclosed Odor fade
and Propane Sheet for additional information about
detecting propane leaks.
11. Install the heater such that it is not directly exposed to
water spray, rain and/or dripping water.
12. Maintain minimum clearance from normal combustible
material (like paper).
Figure 2
.
13. Due to the high surface and exhaust temperatures, adults
and children must observe clearances to avoid burns or
clothing ignition.
14. Operate only on a stable, level surface.
15. Do not use with duct work. Do not restrict inlet or exit.
16. Do not move, handle or service while hot or burning.
17. Use only in accordance with local codes or, in the
absence of local codes, with the Standard for the Storage
and Handling of Liquefied Petroleum Gases ANSI/
NFPA 58 and CSA B149.1, Natural Gas and Propane
Installation Code.
Figure 1
VenTIlaTIOn: Minimum openings required
Opening Opening
Heater
near floor
near ceiling
Convection 80CV, 200CV .................2 ft
2
...................2 ft
2
Figure 2
MInIMuM ClearanCe: From normal combustible material
80CV, 200CV
Clearance Convection
From sides ..................................................4 ft
From top .....................................................6 ft
Locate 10' from canvas or plastic tarpaulins or similar coverings
and secure them to prevent flapping or movement due to wind
action.
CauTIOn! FaIlure TO FOllOw THese VenTIlaTIOn
reQuIreMenTs
MaY resulT In sOOTInG daMaGe.
