S o n o m a U s e r M a n u a l
70
C H A P T E R N I N E
71
S o n o m a U s e r M a n u a l
C O N T R O L A N D S T A T U S C O M M A N D S
lockoutkp
Command to lock out access to the front-panel keypad EDIT
key. See the
kplockstat
and
unlockkp
commands.
netconfig
Interactive script that allows you to configure the IP network
subsystem of the Sonoma.
ntpconfig
Interactive script that guides you in configuring the NTP
Subsystem. Allows configuration of MD5 authentication and
broadcast/multicast mode. All parameters are retained in non-
volatile FLASH disk storage.
ntpstat
Prints the values of several key parameters indicating the status
of the NTP daemon. These include the current offset between
the NTP-steered system clock and the CDMA Subsystem
clock, and the current counts of received packets, sent packets
and dropped packets. In addition the current sent packet rate is
shown.
oscctrlstat
Prints the system oscillator disciplining parameters.
passwd
Used to change the password for the user that you are logged
in as.
ptpconfig0
ptpconfig1
(optional)
Interactive script that guides you in configuring parameters for
the optional PTP/IEEE-1588 protocol. See
Chapter 4 - PTP/
IEEE-1588
for more information.
ptpstat0
ptpstat1
(optional)
Prints the status of the optional PTP/IEEE-1588 Subsystem.
See
Chapter 4 - PTP/IEEE-1588
for more information.
pwrfltmask
(optional)
Prints the current settings of the optional Dual Power Supply
Input Fault Alarm Masks. See
Chapter 10 - Options, Masking
Dual Power Supply Fault Alarms
for more information.
rcvrversion
Prints the CDMA Receiver firmware and FPGA version infor-
mation.
serialnumber
Prints the serial number of the Sonoma. The serial number
is not available using this command for units shipped before
August 2015.
setcaldelay
An interactive utility that allows you to change the clock cali-
bration delay. See the
caldelay
command.
setcdmachannelset
Command that allows the user to select the channelset for the
CDMA Subsystem to receive. This command is not functional
in units comfigured for Japanese Cellular operation.
See the
cdmachannelset
command.
setpwrfltmask
(optional)
Command to enable or mask the optional Dual Power Supply
Input Faults. See
Chapter 10 - Options, Masking Dual Power
Supply Fault Alarms
for more information.
setsigfltmask
Command to enable or mask the Signal Loss Fault.
See the
sigfltmask
command.
sigfltmask
Prints the current setting for the Signal Loss Fault mask.
See the
setsigfltmask
command.
subsysreset
Command that performs a CDMA Subsystem reset.
Summary of Contents for Sonoma D12
