S o n o m a U s e r M a n u a l
102
C H A P T E R E L E V E N
103
S o n o m a U s e r M a n u a l
F R O N T - P A N E L K E Y P A D A N D D I S P L A Y
Display and Keypad
Operation
The display menus are organized as shown below:
Traversing the Display Structure
After power initialization the welcome message will appear. Press any key to go to the Time/Status
display, which is described below. From the Time/Status display, press ENTER or DOWN to go to
the Main Menu. As illustrated in the diagram above, several status and setup displays are accessible
from the Main Menu. To go downward through the structure use the RIGHT and LEFT arrow keys
to highlight a selection and then press ENTER or DOWN. To go back up through the structure press
BACK or UP to return to the previous display.
Editing
To modify a parameter, go to the appropriate display and push EDIT. The edit display will appear
and the modifiable parameter value is highlighted. Use UP and DOWN to scroll through all the pos-
sible parameter values. When editing a sequence of numbers, use LEFT and RIGHT to select other
digits. When the parameter is correct, press ENTER to load the new value. All entered values are
stored in non-volatile FLASH and restored after a power cycle. If you wish to abort the edit process,
press BACK. This will return you to the previous display and the parameter will remain unchanged.
Time / Status
Display
CPU_Stat Receiver Faults Sys_I/O* CPU_I/O* Network NTP PTP* Clock Display Firmware About
Main Menu
Firmware
Information
Contact
Information
Status ChannelSet Osc_Stat Calibrate
Receiver Menu
CDMA
Subsystem
Status
NTP Menu
NTP
Statistics
Broadcast
Multicast
Setup
Time_Mode Time_Zone Hour_Mode Leap_Sec DST
Clock Menu
Time
Mode
Setup
Local
Offset
Setup
Hours
Display
Mode
Leap
Seconds
Setup
CPU
Status
Clock
Calibration
Oscillator
Status
System Receiver SigFltMsk PwrFltMask*
Faults Menu
System
Faults
List
Receiver
Faults
List
Signal
Fault
Mask
Intensity &
Screen
Saver
Status I/O_Stats Setup
NTP
Status
Network4 Network6 MAC_Addr REBOOT
Reboot
System
Eth0 Eth1 DNS
IPv4
Setup
Port Eth0
IPv4
Setup
Port Eth1
DNS
Config
IPv4 Network Menu
IPv6 Network Menu
Eth0 Eth1 DNS
IPv6
Setup
Port Eth0
IPv6
Setup
Port Eth1
DNS
Config
Network Menu
* Optional Display Items. See PTP Chapter and/or Options Chapter for more information.
Daylight
Savings
Setup
CDMA
Channel
Set
Eth0/Eth1
Mac Addr
�
Dual Pwr
Fault
Mask
Summary of Contents for Sonoma D12
