S o n o m a U s e r M a n u a l
118
A P P E N D I X B
119
S o n o m a U s e r M a n u a l
U P G R A D I N G T H E F I R M W A R E
you must begin typing “factory” within five seconds to let the bootloader know that you are going to
override the default kernel. After you hit <enter>
the bootloader will boot the factory kernel. Watch
the rest of the boot process to make sure that you have successfully recovered. If the system boots
normally, then you should resolve the problems with the previous kernel upgrade and re-perform it.
Performing the CDMA Subsystem Upgrade
This section has instructions for upgrading the CDMA Subsystem. If you want to upgrade the
CDMA Receiver see the section below called
Performing the CDMA Receiver Upgrade
.
First you need to download the CDMA Subsystem firmware from the EndRun website to a place on
your network which is accessible to the Sonoma. The link to the Sonoma upgrade page is shown
above.
You may transfer the file to your Sonoma using either
ftp
or
scp
. If you are using
ftp
to perform
the upgrade, transfer the previously downloaded file using
binary
transfer mode from the remote
host to this specific file on your Sonoma:
/tmp/subsys.bin
. The CDMA Subsystem image will be
named with the software part number and version like:
6010-0071-000_3.01.bin
. When following the
instructions below, substitute the name of the actual CDMA Subsystem image that you are installing
for
6010-0071-000_3.01.bin
. You will be transferring the file to a temporary file,
/tmp/subsys.bin
on
your Sonoma.
ftp remote_host
{
perform ftp login on remote host
}
bin
{set transfer mode to binary}
get 6010-0071-000_3.01.bin /tmp/subsys.bin
{transfer the file}
quit
{
close the ftp session after the transfer
}
If you are using SSH to perform the CDMA Subsystem upgrade, you may open another com-
mand window on the remote computer and securely transfer the CDMA Subsystem image to
/tmp/
subsys.bin
using
scp
from the remote computer. A command like this could be used:
scp –p 6010-0071-000_3.01.bin [email protected]:/tmp/subsys.bin
Now issue the following command to the Sonoma console to initiate the upload:
upgradesubsys
This command performs the file transfer to the CDMA Subsystem. You will see a file transfer prog-
ress message while it is performing the transfer. After it completes, wait about 60 seconds and issue
this command to check the CDMA Subsystem version:
cdmaversion
You should see a message like this:
F/W 6010-0071-000 Ver 3.01 - FPGA 6020-0012-000 Ver 01 - JAN 12 15:30:58 2013
The firmware version should match that of the binary file that you uploaded.
Summary of Contents for Sonoma D12
