background image

Soliwave FDR16/FQR16

Hauser

7

Product description

Conversions to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable 

dangers.

 

‣ If, despite this, modifications are required, consult with Hauser.

Repair

Repair is only possible by the manufacturer.

2.5 

Product safety

The devices of the microwave barrier are designed in accordance with good engineering 

practice to meet state-of-the-art safety requirements, has been tested, and left the factory 

in a condition in which it is safe to operate.
They meet general safety standards and legal requirements. They also complies with the 

EU directives listed in the device-specific EU Declaration of Conformity. Hauser 

confirms this by affixing the CE mark to the devices.

Product description

Ultra compact microwave barrier for non-contact point level detection of bulk solids and 

liquids as well as counting piece goods and object detection

3�1 

Product design

A

                                 1                                                                                   2

FQR16                                                                         FDR16

0000000004

1  

Product design

A  Supply and signal circuit 

Connection cable M12 socket 

Connection cable M12 socket/plug

Use in potentially explosive atmospheres → Observe XA!

Summary of Contents for Soliwave FDR16









































Reviews: