Endress+Hauser FQG66 Operating Instructions Manual Download Page 37

Page: 37 / 44

Source container FQG66

Emergency procedure

Hauser

9.2.2

The radiation source is outside from the source container

WARNING

High radioactive radiation

‣

Observe radiation safety rules!

In this case, the radiation source must be placed at a safe location or additional shielding

must be applied.

CAUTION

Handling of the source

‣

The source should only be handled via pliers or tongs and held as far away from the

body as possible.

‣

The time needed for the transport should be estimated and minimized by rehearsal

without radiation source prior to execution.

9.3

Notification to authority

1. Make necessary notifications to local authorities within 24 h.
2. After thorough assessment of the situation, the responsible radiation safety officer,

in conjunction with local authorities, shall agree a remedy to the specific problem.

National regulations may require other procedures and reporting obligations.

Summary of Contents for FQG66













































Search results

Summary of Contents for FQG66

Reviews:

Related manuals for FQG66

Brands by name

Popular brands

Endress+Hauser FQG66, Operating Instructions Manual

Search results

Summary of Contents for FQG66

Reviews:

Related manuals for FQG66

Brands by name

Popular brands