background image

Compact RTD transmitter

Commissioning

Hauser

11

6

Commissioning

6.1

Installation and function check

Installation check

Monitor all connections making sure they are tight. In order to guarantee fault-free 
operation, the terminal screws must be screwed tightly onto the connection cables.

Function check

Measuring the analog 4 to 20 mA output signal or following failure signals as per 
NAMUR NE 43:

6.2

Switch on the device

Once the power supply has been connected, the compact RTD transmitter is 
operational.

6.3

Configuration

6.3.1

Setting up using the PC configuration software

The operating and readout software is an universally applicable service and 
configuration software. The operating software offers the user the following possibilities:

Set-up device functions

Measured value visualization

Device parameter data storage

Measuring point documentation

The compact RTD transmitter left the factory with a default parameter configuration. If 
no customer specific configuration was mentioned on the order then the default 
parameter configuration is constructed as follows:

!

Note! 
If a change has been made to the measurement point then, the compact RTD 
transmitter can be re-configured. In order to re-configure the parameters follow these 
instructions:

Install the configuration software and make connection to the PC (see Chap. 5, 
’Operation’).

For detailed operating instructions for the PC configuration software please read the 
online documentation (

BA137R/09/ae

) contained in the PC operation and readout 

software (see folder ’

Doc

’).

Signal (mA)

Under ranging

Standard

3.8

Over ranging

Standard

20.5

Sensor break; sensor short circuit 
low

To NAMUR NE 43

 3.6

Sensor break; sensor short circuit 
high

To NAMUR NE 43

 21

Sensor

Pt100 (RTD)

Connection mode

4-wire

Measuring range and 
units

0 to +100 °C

Summary of Contents for easytemp TSM 470 F





























Reviews: