manualshive.com logo in svg

Endress+Hauser CleanFit P CPA 472, Operating Instructions Manual, Page: 26 / 31

Share
Download
Endress+Hauser CleanFit P CPA 472 Operating Instructions Manual Download Page 26

CleanFit P CPA 472

6 Accessories

24

Hauser

6.4

Control of retractable assembly during
cleaning / calibration

•

Autoclean CPC 20
Automatic cleaning control for CleanFit retractable assemblies. Control cabinet with 
pneumatic valves, switches for position feedback signal, terminal strip for status sig-
nals. Protection class IP 54.
Technical Information TI 161C/07/en (Order No. 50089137)

•

Liquisys M CPM 223/253
pH and redox measuring transmitter. Integrated electrode function monitoring, 
measured value monitoring, free configuration of alarm contact
Technical Information TI 194C/07/en (Order No. 51500276)

•

Mycom CPM 152
pH/redox field measuring transmitter. Integrated electrode function monitoring, 
alpha value compensation, calibration messages, history memory, menu prompting 
and communication display. Protection class IP 65.
Technical Information TI 143C/07/en (Order No. 50077399)

Summary of Contents for CleanFit P CPA 472
































Reviews:

No comments