Endress+Hauser Cerabar M Operating Instructions Manual Download Page 63

Page: 63 / 92

Cerabar M, Deltapilot M

Diagnostics and troubleshooting

Hauser

Diagnostic event

Cause

Remedial measure

Code

Description

M431 Calibration

The calibration performed would cause the nominal sensor range to be
exceeded or undershot.

• Check the measuring range
• Check the position adjustment
• Check the setting

M434 Scaling

• Values for calibration (e.g. lower range value and upper range value)

are too close together.

• Lower range value and/or upper range value exceed or fall below the

sensor range limits.

• The sensor was replaced and the customer-specific configuration

does not suit the sensor.

• Unsuitable download carried out.

• Check the measuring range
• Check the setting
• Contact Hauser Service

M438 Data record

• The supply voltage is disconnected when writing.
• An error occurred when writing.

• Check the setting
• Restart the device
• Replace the electronics module

M803 Current loop

Impedance of the load resistor at the analog output is too high

• Check the wiring and the load at the current

output

• If the current output is not required, switch it

off via the configuration

• Connect the current output to the load

"S" messages

Diagnostic event

Cause

Remedial measure

Code

Description

S110 Working range T • Excess temperature or low temperature present.

• Electromagnetic effects are greater than specifications in the technical data.
• Sensor defective.

• Check the process temperature
• Check the temperature range

S140 Working range P • Overpressure or negative pressure present.

• Electromagnetic effects are greater than specifications in the technical data.
• Sensor defective.

• Check the process pressure
• Check the sensor range

S822 Process temp.

• The temperature measured in the sensor is greater than the upper nominal tempera-

ture of the sensor.

• The temperature measured in the sensor is lower than the lower nominal tempera-

ture of the sensor.

• Check the temperature
• Check the setting

S841 Sensor range

• Overpressure or low pressure present.
• Sensor defective.

• Check the pressure value
• Contact Hauser Service

S971 Calibration

• The current is outside the permitted range from 3.8 to 20.5 mA.
• The present pressure value is outside the configured measuring range (but may be

within the sensor range).

• Check the pressure value
• Check the measuring range
• Check the setting

Summary of Contents for Cerabar M





























































































Search results

Summary of Contents for Cerabar M

Reviews:

Related manuals for Cerabar M

Brands by name

Popular brands

Endress+Hauser Cerabar M, Operating Instructions Manual

Search results

Summary of Contents for Cerabar M

Reviews:

Related manuals for Cerabar M

Brands by name

Popular brands