background image

12434-7-0706

Page 14

PLEASE NOTE:  When ordering parts, it is very important that  part number and description of part coincide.
Index 

Part

  No. 

Number 

Description

  USE ONLY MANUFACTURER'S REPLACEMENT PARTS.  USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.

  1 

DV-769 

Vent Cap 

  2 

DV-131 

Outside Mounting Plate 

  3 

DV-548 

Air Inlet Tube 

  4 

DV-524 

Flue Outlet Tube 

  5 

DV-757 

Vent Kit

  6 

DV-899 

Wall Mounting Bracket 

  7 

DV-900 

Inlet Air Drop Chute

  8 

DV-762  

Gasket - Air Drop Chute 

 

 

    & DV-763 

(2 Each Required) 

  9 

DV-951 

Casing Top   

  10 

DV-901 

Heat Shield

  11 

DV-902 

Inner Casing (US version)

  11 

15665 

Inner Casing (Canada version)

  12 

RH-705 

Casing Side (2 Required)

  13 

712036 

Gasket - Flue Outlet Support 

  14 

DV-903 

Combustion Chamber (DV-25)

  14 

DV-904 

Combustion Chamber (DV-35)

  15 

712098 

Gasket - Lighting Hole

  16 

DV-781 

Lighting Hole Cover Assembly 

with Clear Mica

  17 

DV-064 

Cover Plate

  18 

DV-988 

Burner (DV-25)

  18 

DV-990 

Burner (DV-35) 

  19 

672063 

Thermopile

  20 

DV-1004 

Pilot Tubing w/Ferrells

  21 

RH-238 

Burner Door

  22 

DV-778 

Gasket - Burner Door

  23 

712051 

Gasket - Pilot Burner

  24 

DV-994 

Pilot Shield

  25 

R-2224 

Pilot Burner with Orifice (Nat)

  25 

R-2223 

Pilot Burner with Orifice (LP)

  26 

DV-772 

Electrode and Wire 

  27 

DV-913 

Casing Front

  28 

742155 

Burner Orifice, (DV-25 Nat)

  28 

742238 

Burner Orifice, (DV-25 LP)

  28 

P-86-38 

Burner Orifice, (DV-35 Nat)

  28 

742233 

Burner Orifice, (DV-35 LP)

  29 

P-190 

Manifold

  30 

R-191 

Manifold Union Assembly

  31 

R-5600 

Gas Valve (Nat) 7000 MVRLC 

  31 

R-5601 

Gas Valve (LP) 7000 MVRLC 

  32 

DV-1003 

Valve Bracket

  33 

DV-764  

Gasket - Chamber Support 

 

 

  & DV-765 

(2 Each Required)

  34 

DV-908 

Valve Shield

  35 

R-2313 

Piezo Ignitor

Not Shown 

742158 

Pilot Orifice (Nat)

Not Shown 

742266 

Pilot Orifice (LP) 

Not Shown 

662021 

Wall Thermostat - Millivolt

Not Shown 

DV-885 

Hardware Package

Not Shown 

922113 

Operator Section - Nat

Not Shown 

922217 

Operator Section - LP

Not Shown 

652121 

Regulator - Nat

Not Shown 

652211 

Regulator - LP

Not Shown 

13298 

Thermostat Bracket

Index 

Part

  No. 

Number 

Description

Parts can be ordered only through your 

service person or dealer

. For best results, the

 service person or dealer 

should order parts through 

the distributor. Parts can be shipped directly to the 

service person/dealer

.

All parts listed in the

 Parts List

 have a 

Part Number

. When ordering parts, first obtain the

 Model Number

 from the name plate on your 

equipment. Then determine the Part Number (

not 

the Index Number) and the Description of each part from the following appropriate 

illustration and list. Be sure to give all this information.
Furnace Model Number 

    Part Description 

Furnace Serial Number  

  Part Number 

Type of Gas (Propane or Natural) 
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store. 
Shipments contingent upon strikes, fires and all causes beyond our control.

Empire Comfort Systems, Inc.  Nine Eighteen Freeburg Ave.   Belleville, IL  62222-0529

HOW TO ORDER REPAIR PARTS

PARTS LIST

Summary of Contents for DV-25-2SG





















Reviews: