background image

19562-3-0907

Page 3

•  Due to high temperatures the appliance should be located 

out of traffic and away from furniture and draperies.

•  Children and adults should be alerted to the hazards of 

high surface temperatures and should stay away to avoid 

burns or clothing ignition.

•  Young children should be carefully supervised when they 

are in the same room as the appliance.

•  Clothing or other flammable material should not be placed 

on or near the appliance.

•  Any  safety  screen  or  guard  removed  for  servicing  an 

appliance  must  be  replaced  prior  to  operating  the 

appliance.

•  Keep burner and control compartment clean. 
•  Vent cap hot while furnace is in operation.
•  For manufactured home (USA only) or mobile home or 

residential installation convertible for use with natural 

gas and liquefied petroleum gases when provision is made 

for the simple conversion from one gas to the other. 

•  Installation and repair should be done by a QUALIFIED 

SERVICE PERSON.  The appliance should be inspected 

before use and at least annually by a qualified service 

person. More frequent cleaning may be required due to 

excessive lint from carpeting, bedding materials, etc. It 

is imperative that control compartments, burners and 

circulating  air  passageways  of  the  appliance  be  kept 

clean.

•  DO  NOT  put  anything  around  the  furnace  that  will 

obstruct the flow of combustion and ventilation air.

•  DO  keep  the  appliance  area  clear  and  free  from 

combustible  material,  gasoline  and  other  flammable 

vapors and liquids.

•  DO  examine  venting  system  periodically  and  replace 

damaged parts.

•  DO make a periodic visual check of burner. Clean and 

replace damaged parts.

•  DO NOT use this heater if any part has been under water. 

Immediately call a qualified service technician to inspect 

the heater and to replace any part of the control system 

and any gas control which has been under water. 

THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.

IMPORTANT SAFETY INFORMATION

Summary of Contents for DV-20E




















Reviews: