background image

Page 1

INSTALLATION  INSTRUCTIONS

AND

OWNER'S  MANUAL

Patent # 5.664.555

WARNING: If not installed, operated and main-

tained  in  accordance  with  the  manufacturer's 

instructions,  this  product  could  expose  you  to 

substances in fuel or from fuel combustion which 

can cause death or serious illness.

FAN TYPE

DIRECT VENT 

WALL FURNACE

For Installation in 

Manufactured (Mobile Home), 

Modular or Residential Homes

MODELS

DV-20

E

DV-40

E

This appliance may be installed as an OEM 

installation in a manufactured home (USA only) 

or mobile home and must be installed in ac-

cordance with the manufacturer's instructions 

and the Manufactured Home Construction and 

Safety Standard, Title 24 CFR, Part 3280, in the 

United States, or the Mobile Home Standard, 

CAN/CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s) 

of gas indicated on the rating plate. A conver-

sion kit is supplied with the appliance.

Installer:  Leave this manual with the appli-

ance.

Consumer: Retain this manual for future refer-

ence.

—  Do not store or use gasoline or other flamma-

ble vapors and liquids in the vicinity of this or 

any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

  •  Do not try to light any appliance.

  •  Do not touch any electrical switch; do not 

use any phone in your building.

  •  Immediately call your gas supplier from a 

neighbor’s  phone.  Follow  the  gas  suppli-

er’s instructions.

  •  If you cannot reach your gas supplier, call 

the fire department.

—  Installation and service must be performed by 

a qualified installer, service agency or the gas 

supplier.

WARNING: If the information in these instruc-

tions are not followed exactly, a fire or explosion 

may result causing property damage, personal 

injury or loss of life.

Summary of Contents for DV-20E




















Reviews: