background image

33742-1-0614

Page 11

33742-1-0614

Page 10

OPTIONAL FRESh AIR KIT INSTALLATION INSTRUcTIONS

OPTIONAL FRESh AIR KIT INSTALLATION INSTRUcTIONS

3.  Insert Slide Assembly through the cut-out as shown in 

Figure 

15

. Before you fasten ensure that the handle penetrates the 

inner firebox wall. 

See Figure 16.

 Fasten the Slide Assembly 

with the four 10 x 1/2 Hex Head Screws provided.

Figure 15

Figure 16

The optional Fresh Air Kit is designed to introduce outside air to 

the firebox as desired.  

It must be installed prior to, or at the time of firebox installation to 

framing.

The Fresh Air kit must be installed prior to the installation of wall

-

board or other finishing materials around the unit.

hardware needed (not provided):

 

4 inch Aluminum Flex Duct, 

 

2 Band Clamps

Tools needed: 

Gloves, Metal snips, 5/16 inch Nut Driver,  

 

Phillips Screwdriver

caution: 

Sharp edges

Slide Assembly Installation

1.  Begin by removing the rectangular cutout located on the left 

side of the unit. Use gloves and sheet metal snips to create 

the opening for the Air Door assembly to install into. See 

Fig-

ure 13

.

Figure 13

2.  Bend the tab out of the way.

 See Figure 14.

Figure 14

4.  Fasten  the  Handle  Retainer  to  the  firebox  side  with  two 

10 x 1/2 Phillips Truss Head Screws as shown in 

Figure 16.

5.  Push the handle for Open position and pull the handle for the 

Closed position. See Figure 17.

Figure 17

completion of Air Kit installation

1.  Determine the length of 4 inch diameter rigid or flex duct con

-

nector (installer supplied) you will need from the firebox/fire

-

place to the exterior surface of the outside wall, where the air 

kit hood will be installed. Add a few extra inches to the length 

to allow for easier attachment of the outside duct connection 

prior to securing the outside rain cap hood to the building.

2.  Secure the 4 inch diameter duct to the Slide Assembly collar 

on the firebox with band clamps or screws (installer supplied).

3.  Run the other end of the duct through the exterior wall cutout.

4.  From the outside of the building, connect the duct to the collar 

on the outside air vent assembly with band clamp or screws 

to secure (installer supplied).

5.  Secure the Outside Air Vent Assembly to the outside wall with 

the four 10 x 1 1/2 Hex Head Slotted Screws provided. Seal 

with caulk as necessary. 

See Figure 18.

6.  Figure 19 illustrates the various options for installation of the 

air duct run possibilities.

Note: 

In  installations  where  the  flex  duct  would  normally  be 

straight (without turns), it is recommended a turn or dip 

be added in the run to reduce air velocity.

OUTSIDE
AIR VENT ASSY

CAULKING

WALL

Caulk and Install Duct Termination

Figure 18

RECOMMENDED TO
ELIMINATE COLD AIR
DRAFT

Figure 19

Summary of Contents for VFP32FB0F-5














Reviews: