Empire Comfort Systems DVCT40CSP95KN-1 Series Installation Instructions Manual Download Page 8

Page: 8 / 44

41521-2-0520

Page 8

SPECIFICATIONS

Model Number

DVCT40NAT

DVCT40LP

Input BTU/Hr Maximum (w/ both burners on)

60,500

55,000

Input BTU/Hr Minimum (w/ both burners on)

40,000

43,000

Input BTU/Hr Minimum (front burner on only)

16,500

26,000

KWH (Maximum)

17.73

16.12

KWH (Minimum)

11.73

12.60

Orifice - Front

#35

#52

Orifice - Rear

#37

1.55 mm

Air Shutter Opening Front

Full Closed

Full Opened

Air Shutter Opening Rear

Full Closed

Full Opened

Height without standoff (inches)

47-1/2

Width (inches)

57-1/4

Depth (inches)

24-3/16

Gas Inlet Shutoff Valve (pipe)

1/2 NPT

NOTE:

Air shutter is at factory-minimum settings. Some vent configurations may require minor air shutter adjustments for optimum performance.

GAS SUPPLY PRESSURES (Inches Water Column)

Gas Type

Maximum

Minimum

Manifold

Natural

4.5

3.5

Propane

10.8

VENTING

LIGHT BULB REPLACEMENT

5 x 8 Direct Vent System

35w Clear Halogen, Bi-Pin 6.35mm base,120vac, UL

ACCESSORIES

The following accessory parts can be obtained from your Empire Comfort Systems dealer. For additional information beyond what your dealer can furnish,
contact Empire Comfort Systems Inc., 918 Freeburg Ave., Belleville, Illinois 62220-2623.

Model Number

ACCESSORIES

Description

DFF40FPD

Decorative Front, Forged Iron Frame, Distressed Pewter

DFF40RPD

Decorative Arch Insert, Forged Iron, Distressed Pewter

DFF40CPD

Decorative Rectangle Insert, Forged Iron, Distressed Pewter (Requires DFF40FPD)

DCA1ABL

Andirons, Black

Model Number

CONVERSION KITS

Description

40636

Conversion Kit, IP System Natural to Propane Gas

40637

Conversion Kit, IP System Propane to Natural Gas

Model Number

OUTDOOR KIT

Description

DFED409SS

Frame, Stainless Steel

Model Number

LOG SETS

Description

LS40STB

Log Set for TruFlame Insert, Fiber - Traditional - Charred

Model Number

LINER KITS

DVP40PS...

A liner is required. Contact your Empire Comfort Systems Dealer for available liners.

NOTE:

A liner kit and log set must be purchased and installed in order to operate the unit. The liner must be installed before installing the logs.

Summary of Contents for DVCT40CSP95KN-1 Series













































Search results

Summary of Contents for DVCT40CSP95KN-1 Series

Reviews:

Related manuals for DVCT40CSP95KN-1 Series

Brands by name

Popular brands

Empire Comfort Systems DVCT40CSP95KN-1 Series, Installation Instructions Manual

Search results

Summary of Contents for DVCT40CSP95KN-1 Series

Reviews:

Related manuals for DVCT40CSP95KN-1 Series

Brands by name

Popular brands