Empire Comfort Systems DVCT40CSP95KN-1 Series Installation Instructions Manual Download Page 41

Page: 41 / 44

41521-2-0520

Page 41

REQUIREMENTS FOR MASSACHUSETTS

For all side wall horizontally vented gas fueled equipment

installed in every dwelling, building or structure used in

whole or in part for residential purposes, including those

owned or operated by the Commonwealth and where the

side wall exhaust vent termination is less than seven feet

above finished grade in the area of the venting, including

but not limited to decks and porches, the following require

ments shall be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETEC

TORS. At the time of installation of the side wall horizon

tal vented gas fueled equipment, the installing plumb

er or gasfitter shall observe that a hard wired carbon

monoxide detector with an alarm and battery back-up

is installed on the floor level where the gas equipment

is to be installed. In addition, the installing plumber or

gasfitter shall observe that a battery operated or hard

wired carbon monoxide detector with an alarm is in

stalled on each additional level of the dwelling, building

or structure served by the side wall horizontal vented

gas fueled equipment. It shall be the responsibility of

the property owner to secure the services of qualified

licensed professionals for the installation of hard wired

carbon monoxide detectors

a. In the event that the side wall horizontally vented

gas fueled equipment is installed in a crawl space

or an attic, the hard wired carbon monoxide detec

tor with alarm and battery back-up may be installed

on the next adjacent floor level.

b. In the event that the requirements of this subdivi

sion can not be met at the time of completion of

installation, the owner shall have a period of thirty

days to comply with the above requirements; pro

vided, however, that during said thirty day period, a

battery operated carbon monoxide detector with an

alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS.

Each carbon monoxide detector as required in accor

dance with the above provisions shall comply with NFPA

720 and be ANSI/UL 2034 listed and IAS certified.

3. SIGNAGE. A metal or plastic identification plate shall

be permanently mounted to the exterior of the building

at a minimum height of eight feet above grade directly

in line with the exhaust vent termination for the horizon

tally vented gas fueled heating appliance or equipment.

The sign shall read, in print size no less than 1/2 inch in

size,

“GAS VENT DIRECTLY BELOW. KEEP CLEAR

OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the

side wall horizontally vented gas fueled equipment shall

not approve the installation unless, upon inspection,

the inspector observes carbon monoxide detectors and

signage installed in accordance with the provisions of

248 CMR 5.08(2)(a) 1 through 4.

(b) EXEMPTIONS: The following equipment is exempt

from 248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled

“Equipment Not Required To Be Vented” in the

most current edition of NFPA 54 as adopted by

the Board; and

2. Product Approved side wall horizontally vent

ed gas fueled equipment installed in a room or

structure separate from the dwelling, building

or structure used in whole or in part for residen

tial purposes.

(d) MANUFACTURER REQUIREMENTS - GAS

EQUIPMENT VENTING SYSTEM NOT PROVID

ED. When the manufacturer of a Product Approved

side wall horizontally vented gas fueled equipment

does not provide the parts for venting the flue gas

es, but identifies “special venting systems”, the fol

lowing requirements shall be satisfied by the manu

facturer:

1. The referenced “special venting system” in

structions shall be included with the appliance

or equipment installation instructions; and

2. The “special venting systems” shall be Product

Approved by the Board, and the instructions for

that system shall include a parts list and de

tailed installation instruction.

(e) A copy of all installation instructions for all Product

Approved side wall horizontally vented gas fueled

equipment, all venting instructions, all parts lists for

venting instructions, and/or all venting design in

structions shall remain with the appliance or equip

ment at the completion of the installation.

Summary of Contents for DVCT40CSP95KN-1 Series













































Search results

Summary of Contents for DVCT40CSP95KN-1 Series

Reviews:

Related manuals for DVCT40CSP95KN-1 Series

Brands by name

Popular brands

Empire Comfort Systems DVCT40CSP95KN-1 Series, Installation Instructions Manual

Search results

Summary of Contents for DVCT40CSP95KN-1 Series

Reviews:

Related manuals for DVCT40CSP95KN-1 Series

Brands by name

Popular brands