background image

Page 1

(SEE HOMEOWNER MANUAL FOR OPERATING INSTRUCTIONS)

INSTALLER: 

Leave this manual with the appliance.

CONSUMER: 

Retain this manual for future reference.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly 

could result in serious injury, death, or 

property damage.

—  Do not store or use gasoline or other 

flammable vapors and liquids in the 

vicinity of this or any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; 

do not use any phone in your building.

•  Leave the building immediately.

•  Immediately call your gas supplier 

from a neighbor’s phone. Follow 

the gas supplier’s instructions.

•  If you cannot reach your gas 

supplier, call the fire department.

—  Installation and service must be 

performed by a qualified installer, 

service agency or the gas supplier.

This appliance may be installed in an aftermarket, 

permanently located, manufactured home (USA 

only)  or  mobile  home,  where  not  prohibited  by 

local codes.
This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is 

not convertible for use with other gases, unless 

a certified kit is used.

This fireplace is design 

certified in accordance 

with American National 

Standard/CSA Standard 

ANSI Z21.88/CSA 2.33 

and by Underwriters 

Laboratories as a Direct 

Vent Gas Fireplace 

Heater and shall be 

installed according to 

these instructions.

GAS-FIRED

 UL FILE NO. MH30033

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

DANGER

A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and shall
be installed for the protection of children and other at-risk
individuals.

DIRECT-VENT 

ZERO CLEARANCE GAS 

FIREPLACE HEATER SERIES: 

DVCT40CSP95KN-1

INSTALLATION INSTRUCTIONS

Summary of Contents for DVCT40CSP95KN-1 Series













































Reviews: