background image

TB-6594

 Page 8 of 12

© 2016 DESCO INDUSTRIES, INC.

Employee Owned

Relay Terminal

The SmartLog Pro™ features a relay terminal that can 

be integrated with electronic door locks, lights, buzzers, 

etc.

Contact Rating

1A @ 30VDC, .5A @ 

125VAC

Maximum Switching Power 30W
Maximum Switching Voltage 250VAC, 220VDC
Maximum Switching Current 1A

7. Tap the Network button to access the Wired

Newtork Setup Menu.  This menu will allow you to

view and edit any network settings if desired.

Figure 10.  Locating the IP address in the Admin Menu

The relay open and close (activation) time may be 

modified using the TEAM5 Software.  See the 

TEAM5 

User Manual

 for more information.

Network Setup

The following procedures will outline how to connect 

your SmartLog Pro™ to a local area network (LAN) 

using its embedded Ethernet communication module.

DYNAMIC IP PROCEDURE

1. Verify that the Ethernet cable is securely connected

to your network and SmartLog Pro™.  The LEDs on

the Ethernet port will illuminate when a connection

to the network is established.

2. The SmartLog Pro™ will automatically obtain an

IP address from the DHCP server.  The IP address

can be located within the Admin Menu.

3. To access the Admin Menu, tap 0 then Enter on the

touchscreen keypad.

4. The SmartLog will prompt for the Admin ID.  Tap 0

then Enter.

5. The SmartLog will prompt for the Admin PIN.  Tap 0

then Enter.

6. The Admin Menu will appear.  The IP address

can be found in the top left corner.  Take note

of this address as it will be required to establish

communication between the SmartLog Pro and the

TEAM5 Server Software.

Normally Closed
Common
Normally Open

Figure 9.  Relay terminal contacts located on the back of 

the SmartLog Pro™

Figure 11.  Locating the Newtork button in the Admin 

Menu

Figure 12.  Wired Network Setup menu

Summary of Contents for SmartLog Pro 50780


















Reviews: