EMIT ETS 2 User Manual Download Page 17 | Manualshive

Page: 17 / 20

background image

Spool

(main menu – spool)

Press 'All' to resend all data stored in the ETS2.

Use this function with caution. If

the ETS2 has a lot of data stored, it will be busy resending data for some
minutes, and will not send new data before all the old data is transferred.

Press 'Day' to resend all data collected today.
Press 'Stop' to stop resending data.

eUpgrade

eUpgrade is a program - provided for free by Emit – that is used to upgrade the internal
firmware version of the ETS2. The program may be downloaded from

http://195.159.103.189/software/

PLEASE ONLY USE EUPGRADE IF YOU KNOW YOUR ETS2 NEEDS UPGRADING!

After downloading and installing the program, connect ETS2 to an available USB-port
and start eUpgrade.
At the top of the screen eUpgrade displays the equipment type (ETS2), hardware type
(2), software version (2.1) and serial number (876100440). Please note that the software
version must match the hardware type; to use software version 2.x the ETS2 must have
hardware type 2.

«
...
15
16
17
18
19
...
»

Summary of Contents for ETS 2





















Reviews:

No comments

Related manuals for ETS 2

Brand: Timex Pages: 8

Brand: Memorex Pages: 11

Brand: Manta Pages: 16

Brand: Salora Pages: 21

Brand: ICStation Pages: 5

Brand: IKEA Pages: 8

Brand: Masterclock Pages: 38

Brand: Seiko Pages: 36

Brand: Datexx Pages: 1

Brand: Sanyo Pages: 34

Brand: Honeywell Pages: 9

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

DREAM MACHINE ICF-C430

Brand: Sony Pages: 16

Brand: Onaroo Pages: 7

2G-StarLink TrackerSF

Brand: ERM Pages: 17

Brand: Equity Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands