EMIT ETS 2 User Manual Download Page 20

Page: 20 / 20

TECHNICAL SPECIFICATIONS ETS2 v.2.1

Dimensions: 41x33x18cm

Weight: 7.5Kg

Operating temperature: -20 to 70°C

Relative humidity: 45%

Power supply: 110-230V~ 50/60Hz 40W

Inputs: Two wired inputs (Start/sync, Finish) + two radio receivers (868Mhz)

Outputs: Two external eLine-loop o one internal eLine-loop

Serial interfaces: USB (FTDI), RS232, RS485, 115200 bit/s, 1 stop bit, no parity

Data outputs: USB, printer, LCD, 4G modem.

The S, mS, 1/10000s and uS accuracy is only available on 'Start/sync'

and 'Finish' input. It is not available for emiTag-registrations.

Temperature stability: +/- 2 PPM (0°C to +40°C) / +/- 7.5 PPM (-40°C to +85°C)

Quartz Ageing: +/- 1.0 PPM (first year)

Temperature stability (24Hours 23°C): +/-0.2ppm with calibration without charger
after two hours.

Battery life: 24 hours

Hardware Version: 81405-2

Firmware Version: V2.1

Protection code: IP67

Summary of Contents for ETS 2





















Search results

Summary of Contents for ETS 2

Reviews:

Related manuals for ETS 2

Brands by name

Popular brands

EMIT ETS 2, User Manual

Search results

Summary of Contents for ETS 2

Reviews:

Related manuals for ETS 2

Brands by name

Popular brands