Emerson EIM TEC2 500 Quick Start Manual Download Page 3 | Manualshive

Page: 3 / 18

background image

Welcome to TEC2

September 2018

Quick-Start Guide

E2K-210-05-18 Rev. 3

1

Welcome to TEC2

Welcome to TEC2

The TEC2 actuator’s Local Display Module (LDM) and Remote Display Module (RDM) provide easy-to-read
actuator information.

The screen graphics will display the mode of operation, valve status, position, torque, and alarm symbols.
The message center will display actuator setup options, data entry feedback, and alarm messages.

Once you follow the simple steps outlined in this guide, the actuator will be ready for normal operation.
The bar graph, position digits, icons, and LEDs will indicate the valve status.

LED Indicators

Valve Torque

Display Diagnostic

Operating
Mode

Moving Status

«
1
2
3
4
5
...
»

Summary of Contents for EIM TEC2 500



















Reviews:

No comments

Related manuals for EIM TEC2 500

Brand: Bartlett Pages: 30

Brand: S&C Pages: 40

Brand: NEC Pages: 304

Brand: 1Control Pages: 8

Brand: Eaton Pages: 6

Brand: D+H Pages: 36

Brand: D-Box Pages: 4

Brand: D+H Pages: 36

Brand: Daikin Pages: 38

Brand: Daikin Pages: 2

Brand: Daikin Pages: 148

Brand: Daikin Pages: 12

Brand: Daktronics Pages: 52

Brand: Waeco Pages: 20

Brand: Z-Wave Pages: 56

Brand: Data I/O Pages: 88

Brand: Data Aire Pages: 13

Brand: Harman Kardon Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands