Emerson EIM TEC2 500 Quick Start Manual Download Page 10

Page: 10 / 18

Check the Open/Closed Settings

Quick-Start Guide

E2K-210-05-18 Rev. 3

September 2018

Check the Open/Closed Settings

Check the

Open/Closed Settings

Valve Closed

As you operate the valve in the close direction, verify
that the

green LED

is blinking. When fully closed is

reached, verify that the

green LED

stays

and

is displayed.

When turning to close,
green LED blinks.

When fully closed,
green LED remains lit.

Valve Open

As you operate the valve in the open direction, verify
that the

red LED

is blinking. When fully open is

reached, verify that the

red LED

stays

and

100%

is displayed.

When turning to
open, red LED blinks.

When fully open,
red LED remains lit.

Note

It is also configurable to have a

red LED

for

Valve Closed

Note

It is also configurable to have a

green LED

for

Valve Open

Summary of Contents for EIM TEC2 500



















Search results

Summary of Contents for EIM TEC2 500

Reviews:

Related manuals for EIM TEC2 500

Brands by name

Popular brands

Emerson EIM TEC2 500, Quick Start Manual

Search results

Summary of Contents for EIM TEC2 500

Reviews:

Related manuals for EIM TEC2 500

Brands by name

Popular brands