Emerson EC2-552 Installing And Operating Instructions Download Page 21

Page: 21 / 54

OI_EC2-XC645CX_A1_A2L_A3_EN_Rev01_866933.docx EC2-XC645CX

21/54

NOTE:

Also the “cPr2”, “InC2”, “dGs”, “inC1”, ”and “dGSt” values are present. These values

must

not

be used.

According to the oA2, oA3, oA4, oA6 configuration, 2 kinds of plant can be defined:

Rack with compressors only:

all the oAi different from FAn and inF

Rack with compressors and fans:

both FAn and CPr are used for oAi.

NOTE: COMPRESSOR WITH STEPS CONFIGURATION:

the output of compressor has to be

set before the output of the step.

ES.

Compressor with 1 step:

oA2 = cPr1, oA3= StP.

If an oAi set as step without any previous oAi set as cPr the configuration alarm “CStP”

will be activated.

PLANT CONFIGURATION EXEMPLES:

Plant with 2 compressors

(one of them digital) e 2 fans:

oA1 = dgS

oA2 = CPr1

oA3 = FAn

oA4 = FAn

oA6 = nu

Plant with 4 compressors

without fans:

oA1 = dgS

oA2 = CPr1

oA3 = CPr1

oA4 = CPr1

oA6 = nu

Plant with 1 compressor and

3 fans:

oA1 = dgS

oA2 = FAn

oA3 = FAn

oA4 = FAn

oA6 = nu

24V

24V

Summary of Contents for EC2-552























































Search results

Summary of Contents for EC2-552

Reviews:

Related manuals for EC2-552

Brands by name

Popular brands

Emerson EC2-552, Installing And Operating Instructions

Search results

Summary of Contents for EC2-552

Reviews:

Related manuals for EC2-552

Brands by name

Popular brands