Emerson EC2-552 Installing And Operating Instructions Download Page 10

Page: 10 / 54

OI_EC2-XC645CX_A1_A2L_A3_EN_Rev01_866933.docx EC2-XC645CX

10/54

5.4 Load connections

!!!WARNING: Digital Scroll valve coil MUST operate at main voltage (24 VAC)!

NOTE:

Main voltage side

(6 PINs connector): the PIN 17 is the common

line for all the relay outputs

and for the TRIAC.

5.5 Safety and configurable digital inputs – free voltage

Loads safety inputs

!!!WARNING: free voltage inputs

!!!!

Controller has 7 configurable digital inputs,

free voltage

Each digital input can be set by the related parameter iF01 - iF07.

The digital inputs are factory pre-set to operate as safety input for loads and as HP and LP. This

input has to collect the status of the safety devices related to the compressor such as thermistors,

pressure switches etc.

When this input is activated the correspondence, load is switched off and not considered for the

regulation.

The correspondence between loads (compressors or fans) and safety inputs is the following:

LOAD

TERMINALS

INPUT

TERMINALS

SETTING

Load 1

15-17

Di1

10-13

iF01 = oA1

Load 2

16-17

Di2

10-14

iF02 = oA2

Load 3

18-17

Di3

10-11

iF03 = oA3

Load 4

20-17

Di4

10-12

iF04 = oA4

Load 6

21-22

Di7

27-28

iF07 = oA6

Circuit with 1 SUCTION and 1 CONDENSER: HP – LP Pressure

switch connections

The controller is preset to manage also the

low-pressure switch

and the

high-pressure switch,

both the inputs are

free voltage.

Connect the pressure switches as described in the following table:

PRESSURE SWITCH

INPUT

TERMINALS

SETTING

Di5

10-9

iF05 = LP1

HP*

Di6

25-26

iF06 = HP

Note: *) The digital input 6 (25-26) requires the adapter CABCJ15 or CABCJ30 to be used.

See par.

Error! Reference source not found.

24VAC

Summary of Contents for EC2-552























































Search results

Summary of Contents for EC2-552

Reviews:

Related manuals for EC2-552

Brands by name

Popular brands

Emerson EC2-552, Installing And Operating Instructions

Search results

Summary of Contents for EC2-552

Reviews:

Related manuals for EC2-552

Brands by name

Popular brands