Emerson Daniel PT Installation And Maintenance Instructions Manual Download Page 9

Page: 9 / 56

Contents

Dimensions and specifications..................................................................................... 13

Chapter 2

Product handling......................................................................................................... 21

2.1 Packaging and shipping of the “PT” Meter...................................................................................... 21
2.2 Meter service and storage...............................................................................................................21

Part II Install

Chapter 3

Installation and initial operation.................................................................................. 25

3.1 Intallation requirements.................................................................................................................25

Part III Operate

Chapter 4

Turbine meter instrumentation....................................................................................33

4.1 Connection of the Turbine Meter to the Readout............................................................................33

Part IV Maintain

Chapter 5

Disassembly and assembly instructions........................................................................39

5.1  3" through 24" PT Meter disassembly..............................................................................................39
5.2  3" through 24" PT Meter assembly.................................................................................................. 47
5.3  Parts inspection..............................................................................................................................53

Installation and maintenance instructions

Contents

3-9008-011

October 2019

Installation and maintenance instructions

Summary of Contents for Daniel PT

























































Search results

Summary of Contents for Daniel PT

Reviews:

Related manuals for Daniel PT

Brands by name

Popular brands

Emerson Daniel PT, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for Daniel PT

Reviews:

Related manuals for Daniel PT

Brands by name

Popular brands