background image

P6    SYNCHRONIZATION

5. For advanced cam settings, the design of the shaft has

been divided into 28 directions to customize water flow for

your installation. Each of them is around 13 degrees from the

other. Users may select partial open, semi-open, partial close,

etc.). These settings are not listed in the chart. The 12 o’clock

(small slot) is always the reference of every setting (Fig. 2).

The upper cam affects the clockwise position stop point. The

lower cam affects the counter-clockwise rotation stop point.

6. The toggle switch on the bottom of the valve actuator can

be used to verify if the new adjustment is correct (switch

between ON1 and ON2).

7. Replace cover and handle and tighten screws and the

locking knob.

8. Put

toggle switch back to ON1 or ON2 position.

the

Fig. 5

Advanced cam setting should be performed by pool technician.

Note:

3.5 Synchronization

A typical pool with a spa might have 3-6 diverter valves to control the flow of water through the pool

and spa. If one is rotating in the opposite direction to the other, the actuators have to be adjusted to

bring them into Sync. Simply flip the toggle switch of the Actuator between ON1 and ON2.

3.6 Manual Override (MO)

Turn power OFF to all filtration pumps before doing this action, to minimize the

possibility of any injury or damage.

CAUTION

1. Turn the toggle switch to the OFF position.

2. Unscrew anti clockwise the knob for 1 turn approximately.

3. Push down the handle and knob. This will disengage the gear train and allow the handle, thus the

diverter, to move to any position.

4. Make sure to turn the actuator to the automatic position after manual override. Turn clockwise or

counter clockwise slightly until you feel the shaft slide up into the gear train. Then, turn the knob

clockwise to lock the handle.

5. Tighten the knob.

6. Flip toggle switch back to the original position.

The valve position may have to be adjusted manually when necessary. This happens when the controller

is not accessible or following a power failure. Follow the instructions below.

Summary of Contents for 91609013















Reviews: