background image

P4    BASIC CAM SETTING

3.1 Basic cam setting

Test your Actuator

a. Default

b. If you need to make adjustment

Both upper and lower CAM are

pointing to the “12 o’clock”

Connect your actuator to control system

Use manual mode to test arrow position

Refer to 3.3 and 3.4 to adjust.

Fig. 2

(3-way valve)

Use the chart to determine the correct basic cam setting by

using standard clock positions. The

below shows the cam

settings for 3-way valves.

chart

Mounting

option

Inlet

(Water enters port)

Basic Cam Setting

Port Where Water Exits

UPPER CAM

LOWER CAM

Port

Port

A

(standard)

1

9 o'clock

6 o'clock

2

3

2

(standard)

12 o'clock

12 o'clock

1

3

3

6 o'clock

3 o'clock

1

2

B

1

12 o'clock

9 o'clock

2

3

2

3 o'clock

3 o'clock

1

3

3

9 o'clock

6 o'clock

1

2

C

1

6 o'clock

3 o'clock

2

3

2

9 o'clock

9 o'clock

1

3

3

3 o'clock

12 o'clock

1

2

D

1

3 o'clock

12 o'clock

2

3

2

6 o'clock

6 o'clock

1

3

3

12 o'clock

9 o'clock

1

2

(2-way valve)

For the actuators mounted on 2-way valves. the cam settings are the same

. The

shows

the cam settings for 2-way valves.

in all cases

chart

Basic Cam Setting

UPPER CAM

LOWER CAM

3 o’clock

6 o’clock

Summary of Contents for 91609013















Reviews: