background image

ELKC1M1 4GSM ElkCommBd Communicator

Page 2

HARDWARE OVERVIEW

7 Segment Display

Displays 1 alphanumeric character at a time 

sequentially to reveal: Signal Strength, Error 

Codes, IP Address.  Data is grouped in short 

packets preceded by a key letter.  In process 

communications is also displayed.  

b

  

b

ars of cell signal - The letter is followed by a 

single digit from 0 to 5.  

 Example: 

b 3

 reveals 3 bars of service.  

E

  

E

rrors - The letter is followed by two digits.   

Examples of error codes are: 

E01

  =  Application not loaded

E0 2 

=  Radio Module Power Fail

E0 3

  =  No SIM card installed.

E0 4 

=  Inactive Unit 

E0 5

  =  Low (Poor) Signal Strength

E0 6

  =  No Service or unregistered on Cell 

Network

E0 7

  =  Unable to communicate with M1

E0 8

  =  Cellular radio module not detected

E0 9

  =  No Internet Service (LAN detected)

E1 0

  =  No LAN detected (check cable)

E1 1

  =  Central Station not configured in 

ElkLink

E1 2

  =  CS Receiver failed to respond

E1 3

  =  No DHCP Server found

A

  

A

ddress - The LAN IP address is displayed 

1  character  at  a  time  during  the  first  2 

minutes after power up.  C1M1 supports 

IPv4 addresses.  These consist of 4 octets 

having a value of 0 to 255.  Each octet will be 

separated by a decimal point.  

       Example:   

A 1 9 2 . 1 6 8 . 0 . 1 0 0

  NOTE: CS reports take priority over the display 

of the LAN IP address which could make 

it  difficult  to  view  the  address  sequentially 

during power up.  The LAN IP address display 

may be repeated by removing the cover from 

the C1M1 and then pressing the small rubber 

plunger of the tamper switch button 5 times 

quickly.  Replace the cover when done.    

Communications Activity:  

0

  Communications to the Central Station will  be 

displayed as a clockwise rotation of the outer 6 

elements on the display.  A decimal point in the 

the lower right corner will illuminate if the report 

is being send by IP (Ethernet).

8

  Communications to ElkLink will be displayed 

as a figure 8 circulation of all 7 elements on the 

display.

o  

Communications via the USB serial port will 

be displayed as a clockwise rotation of the lower 

4 elements on the display.

Dipole Antenna

Cell  (Service) Red LED

Normal = ON solid.  This indicates that a 

Cell tower is within range and the unit has 

established a connection.  

Blinking indicates limited or no service.

LAN (Activity) Green LED

Normal = Blinking.  This indicates that 

communications is occurring with the Local 

Area Network (LAN) 

ElkLink (Connect) Orange/Yel LED

Normal = ON solid.  This indicates that 

C1M1 has an established connection with 

the ElkLink portal.  Note: A continuous 

connection to ElkLink is not mission 

critical for CS reporting.  This LED may 

occasionally be off for short time periods.  

Removable Terminal Block

Power Input (12 VDC)

This power shall be supplied from an Aux. 

Power output on the M1 Control.

Input

Not currently enabled - future use   

RS232 Cable (3 Wire)

C1M1 ships with a 36" serial cable plugged 

into this port.  A DB9M connector on the 

other end of this cable plugs directly to the 

Main RS232 Serial Port on the M1 Control.  

LAN (IP) Port

For connection to client's LAN (Local Area 

Network) for Dual Path communications.  If 

LAN is not available, C1M1 may be used in 

single path (Cellular Only) operation mode.

Per UL requirements, when utilizing the 

LAN (IP) Port an Isolated Loop Circuit 

Protector mfg by APC  Model #PNET1GB 

shall be purchased and installed.

USB Port (Mini B)

Allows local ELK-RP programming of M1 

using a PC and a USB serial cable.

Output

Not currently enabled - future use

WARNING: Max. Cable Length is 36"

Do NOT disconnect, splice or extend this 

serial cable.  Evidence of such action will 

VOID PRODUCT WARRANTY.

Summary of Contents for ELK-C1M1 4GSM ElkCommBd













Reviews: